| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
media: v4l2-async: Fix error handling on steps after finding a match
Once an async connection is found to be matching with an fwnode, a
sub-device may be registered (in case it wasn't already), its bound
operation is called, ancillary links are created, the async connection
is added to the sub-device's list of connections and removed from the
global waiting connection list. Further on, the sub-device's possible own
notifier is searched for possible additional matches.
Fix these specific issues:
- If v4l2_async_match_notify() failed before the sub-notifier handling,
the async connection was unbound and its entry removed from the
sub-device's async connection list. The latter part was also done in
v4l2_async_match_notify().
- The async connection's sd field was only set after creating ancillary
links in v4l2_async_match_notify(). It was however dereferenced in
v4l2_async_unbind_subdev_one(), which was called on error path of
v4l2_async_match_notify() failure. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: amlogic: spifc-a4: unregister ECC engine on probe failure and remove() callback
aml_sfc_probe() registers the on-host NAND ECC engine, but teardown was
missing from both probe unwind and remove-time cleanup. Add a devm cleanup
action after successful registration so
nand_ecc_unregister_on_host_hw_engine() runs automatically on probe
failures and during device removal. |
| In the Linux kernel, the following vulnerability has been resolved:
ceph: do not propagate page array emplacement errors as batch errors
When fscrypt is enabled, move_dirty_folio_in_page_array() may fail
because it needs to allocate bounce buffers to store the encrypted
versions of each folio. Each folio beyond the first allocates its bounce
buffer with GFP_NOWAIT. Failures are common (and expected) under this
allocation mode; they should flush (not abort) the batch.
However, ceph_process_folio_batch() uses the same `rc` variable for its
own return code and for capturing the return codes of its routine calls;
failing to reset `rc` back to 0 results in the error being propagated
out to the main writeback loop, which cannot actually tolerate any
errors here: once `ceph_wbc.pages` is allocated, it must be passed to
ceph_submit_write() to be freed. If it survives until the next iteration
(e.g. due to the goto being followed), ceph_allocate_page_array()'s
BUG_ON() will oops the worker.
Note that this failure mode is currently masked due to another bug
(addressed next in this series) that prevents multiple encrypted folios
from being selected for the same write.
For now, just reset `rc` when redirtying the folio to prevent errors in
move_dirty_folio_in_page_array() from propagating. Note that
move_dirty_folio_in_page_array() is careful never to return errors on
the first folio, so there is no need to check for that. After this
change, ceph_process_folio_batch() no longer returns errors; its only
remaining failure indicator is `locked_pages == 0`, which the caller
already handles correctly. |
| In the Linux kernel, the following vulnerability has been resolved:
dm mpath: Add missing dm_put_device when failing to get scsi dh name
When commit fd81bc5cca8f ("scsi: device_handler: Return error pointer in
scsi_dh_attached_handler_name()") added code to fail parsing the path if
scsi_dh_attached_handler_name() failed with -ENOMEM, it didn't clean up
the reference to the path device that had just been taken. Fix this, and
steamline the error paths of parse_path() a little. |
| An authorization issue was addressed with improved state management. This issue is fixed in iOS 18.7.9 and iPadOS 18.7.9, iOS 26.4 and iPadOS 26.4, macOS Sequoia 15.7.5, macOS Sonoma 14.8.5, macOS Tahoe 26.4, visionOS 26.4, watchOS 26.4. An app may be able to access sensitive user data. |
| A logic issue was addressed with improved restrictions. This issue is fixed in macOS Sequoia 15.7.5, macOS Sonoma 14.8.5, macOS Tahoe 26.4. A malicious app may be able to break out of its sandbox. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw89: sar: drop lockdep assertion in rtw89_set_sar_from_acpi
The following assertion is triggered on the rtw89 driver startup. It
looks meaningless to hold wiphy lock on the early init stage so drop the
assertion.
WARNING: CPU: 7 PID: 629 at drivers/net/wireless/realtek/rtw89/sar.c:502 rtw89_set_sar_from_acpi+0x365/0x4d0 [rtw89_core]
CPU: 7 UID: 0 PID: 629 Comm: (udev-worker) Not tainted 6.15.0+ #29 PREEMPT(lazy)
Hardware name: LENOVO 21D0/LNVNB161216, BIOS J6CN50WW 09/27/2024
RIP: 0010:rtw89_set_sar_from_acpi+0x365/0x4d0 [rtw89_core]
Call Trace:
<TASK>
rtw89_sar_init+0x68/0x2c0 [rtw89_core]
rtw89_core_init+0x188e/0x1e50 [rtw89_core]
rtw89_pci_probe+0x530/0xb50 [rtw89_pci]
local_pci_probe+0xd9/0x190
pci_call_probe+0x183/0x540
pci_device_probe+0x171/0x2c0
really_probe+0x1e1/0x890
__driver_probe_device+0x18c/0x390
driver_probe_device+0x4a/0x120
__driver_attach+0x1a0/0x530
bus_for_each_dev+0x10b/0x190
bus_add_driver+0x2eb/0x540
driver_register+0x1a3/0x3a0
do_one_initcall+0xd5/0x450
do_init_module+0x2cc/0x8f0
init_module_from_file+0xe1/0x150
idempotent_init_module+0x226/0x760
__x64_sys_finit_module+0xcd/0x150
do_syscall_64+0x94/0x380
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Found by Linux Verification Center (linuxtesting.org). |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: add a retry logic in net6_rt_notify()
inet6_rt_notify() can be called under RCU protection only.
This means the route could be changed concurrently
and rt6_fill_node() could return -EMSGSIZE.
Re-size the skb when this happens and retry, removing
one WARN_ON() that syzbot was able to trigger:
WARNING: CPU: 3 PID: 6291 at net/ipv6/route.c:6342 inet6_rt_notify+0x475/0x4b0 net/ipv6/route.c:6342
Modules linked in:
CPU: 3 UID: 0 PID: 6291 Comm: syz.0.77 Not tainted 6.16.0-rc7-syzkaller #0 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
RIP: 0010:inet6_rt_notify+0x475/0x4b0 net/ipv6/route.c:6342
Code: fc ff ff e8 6d 52 ea f7 e9 47 fc ff ff 48 8b 7c 24 08 4c 89 04 24 e8 5a 52 ea f7 4c 8b 04 24 e9 94 fd ff ff e8 9c fe 84 f7 90 <0f> 0b 90 e9 bd fd ff ff e8 6e 52 ea f7 e9 bb fb ff ff 48 89 df e8
RSP: 0018:ffffc900035cf1d8 EFLAGS: 00010293
RAX: 0000000000000000 RBX: ffffc900035cf540 RCX: ffffffff8a36e790
RDX: ffff88802f7e8000 RSI: ffffffff8a36e9d4 RDI: 0000000000000005
RBP: ffff88803c230f00 R08: 0000000000000005 R09: 00000000ffffffa6
R10: 00000000ffffffa6 R11: 0000000000000001 R12: 00000000ffffffa6
R13: 0000000000000900 R14: ffff888032ea4100 R15: 0000000000000000
FS: 00007fac7b89a6c0(0000) GS:ffff8880d6a20000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fac7b899f98 CR3: 0000000034b3f000 CR4: 0000000000352ef0
Call Trace:
<TASK>
ip6_route_mpath_notify+0xde/0x280 net/ipv6/route.c:5356
ip6_route_multipath_add+0x1181/0x1bd0 net/ipv6/route.c:5536
inet6_rtm_newroute+0xe4/0x1a0 net/ipv6/route.c:5647
rtnetlink_rcv_msg+0x95e/0xe90 net/core/rtnetlink.c:6944
netlink_rcv_skb+0x155/0x420 net/netlink/af_netlink.c:2552
netlink_unicast_kernel net/netlink/af_netlink.c:1320 [inline]
netlink_unicast+0x58d/0x850 net/netlink/af_netlink.c:1346
netlink_sendmsg+0x8d1/0xdd0 net/netlink/af_netlink.c:1896
sock_sendmsg_nosec net/socket.c:712 [inline]
__sock_sendmsg net/socket.c:727 [inline]
____sys_sendmsg+0xa95/0xc70 net/socket.c:2566
___sys_sendmsg+0x134/0x1d0 net/socket.c:2620 |
| In the Linux kernel, the following vulnerability has been resolved:
clk: spacemit: mark K1 pll1_d8 as critical
The pll1_d8 clock is enabled by the boot loader, and is ultimately a
parent for numerous clocks, including those used by APB and AXI buses.
Guodong Xu discovered that this clock got disabled while responding to
getting -EPROBE_DEFER when requesting a reset controller.
The needed clock (CLK_DMA, along with its parents) had already been
enabled. To respond to the probe deferral return, the CLK_DMA clock
was disabled, and this led to parent clocks also reducing their enable
count. When the enable count for pll1_d8 was decremented it became 0,
which caused it to be disabled. This led to a system hang.
Marking that clock critical resolves this by preventing it from being
disabled.
Define a new macro CCU_FACTOR_GATE_DEFINE() to allow clock flags to
be supplied for a CCU_FACTOR_GATE clock. |
| In Modem IMS, there is a possible improper input validation. This could lead to remote denial of service with no additional execution privileges needed. |
| In the Linux kernel, the following vulnerability has been resolved:
LoongArch: Set hugetlb mmap base address aligned with pmd size
With ltp test case "testcases/bin/hugefork02", there is a dmesg error
report message such as:
kernel BUG at mm/hugetlb.c:5550!
Oops - BUG[#1]:
CPU: 0 UID: 0 PID: 1517 Comm: hugefork02 Not tainted 6.14.0-rc2+ #241
Hardware name: QEMU QEMU Virtual Machine, BIOS unknown 2/2/2022
pc 90000000004eaf1c ra 9000000000485538 tp 900000010edbc000 sp 900000010edbf940
a0 900000010edbfb00 a1 9000000108d20280 a2 00007fffe9474000 a3 00007ffff3474000
a4 0000000000000000 a5 0000000000000003 a6 00000000003cadd3 a7 0000000000000000
t0 0000000001ffffff t1 0000000001474000 t2 900000010ecd7900 t3 00007fffe9474000
t4 00007fffe9474000 t5 0000000000000040 t6 900000010edbfb00 t7 0000000000000001
t8 0000000000000005 u0 90000000004849d0 s9 900000010edbfa00 s0 9000000108d20280
s1 00007fffe9474000 s2 0000000002000000 s3 9000000108d20280 s4 9000000002b38b10
s5 900000010edbfb00 s6 00007ffff3474000 s7 0000000000000406 s8 900000010edbfa08
ra: 9000000000485538 unmap_vmas+0x130/0x218
ERA: 90000000004eaf1c __unmap_hugepage_range+0x6f4/0x7d0
PRMD: 00000004 (PPLV0 +PIE -PWE)
EUEN: 00000007 (+FPE +SXE +ASXE -BTE)
ECFG: 00071c1d (LIE=0,2-4,10-12 VS=7)
ESTAT: 000c0000 [BRK] (IS= ECode=12 EsubCode=0)
PRID: 0014c010 (Loongson-64bit, Loongson-3A5000)
Process hugefork02 (pid: 1517, threadinfo=00000000a670eaf4, task=000000007a95fc64)
Call Trace:
[<90000000004eaf1c>] __unmap_hugepage_range+0x6f4/0x7d0
[<9000000000485534>] unmap_vmas+0x12c/0x218
[<9000000000494068>] exit_mmap+0xe0/0x308
[<900000000025fdc4>] mmput+0x74/0x180
[<900000000026a284>] do_exit+0x294/0x898
[<900000000026aa30>] do_group_exit+0x30/0x98
[<900000000027bed4>] get_signal+0x83c/0x868
[<90000000002457b4>] arch_do_signal_or_restart+0x54/0xfa0
[<90000000015795e8>] irqentry_exit_to_user_mode+0xb8/0x138
[<90000000002572d0>] tlb_do_page_fault_1+0x114/0x1b4
The problem is that base address allocated from hugetlbfs is not aligned
with pmd size. Here add a checking for hugetlbfs and align base address
with pmd size. After this patch the test case "testcases/bin/hugefork02"
passes to run.
This is similar to the commit 7f24cbc9c4d42db8a3c8484d1 ("mm/mmap: teach
generic_get_unmapped_area{_topdown} to handle hugetlb mappings"). |
| In the Linux kernel, the following vulnerability has been resolved:
rnbd-srv: Zero the rsp buffer before using it
Before using the data buffer to send back the response message, zero it
completely. This prevents any stray bytes to be picked up by the client
side when there the message is exchanged between different protocol
versions. |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: sysfs: fix chip removal with GPIOs exported over sysfs
Currently if we export a GPIO over sysfs and unbind the parent GPIO
controller, the exported attribute will remain under /sys/class/gpio
because once we remove the parent device, we can no longer associate the
descriptor with it in gpiod_unexport() and never drop the final
reference.
Rework the teardown code: provide an unlocked variant of
gpiod_unexport() and remove all exported GPIOs with the sysfs_lock taken
before unregistering the parent device itself. This is done to prevent
any new exports happening before we unregister the device completely. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/ioc32: stop speculation on the drm_compat_ioctl path
The drm compat ioctl path takes a user controlled pointer, and then
dereferences it into a table of function pointers, the signature method
of spectre problems. Fix this up by calling array_index_nospec() on the
index to the function pointer list. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Adjust PHY FSM transition to TX_EN-to-PLL_ON for TMDS on DCN35
[Why]
A backport of the change made for DCN401 that addresses an issue where
we turn off the PHY PLL when disabling TMDS output, which causes the
OTG to remain stuck.
The OTG being stuck can lead to a hang in the DCHVM's ability to ACK
invalidations when it thinks the HUBP is still on but it's not receiving
global sync.
The transition to PLL_ON needs to be atomic as there's no guarantee
that the thread isn't pre-empted or is able to complete before the
IOMMU watchdog times out.
[How]
Backport the implementation from dcn401 back to dcn35.
There's a functional difference in when the eDP output is disabled in
dcn401 code so we don't want to utilize it directly. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/tegra: Fix NULL vs IS_ERR() check in probe()
The iommu_paging_domain_alloc() function doesn't return NULL pointers,
it returns error pointers. Update the check to match. |
| In Modem IMS, there is a possible improper input validation. This could lead to remote denial of service with no additional execution privileges needed. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: SMP: derive legacy responder STK authentication from MITM state
The legacy responder path in smp_random() currently labels the stored
STK as authenticated whenever pending_sec_level is BT_SECURITY_HIGH.
That reflects what the local service requested, not what the pairing
flow actually achieved.
For Just Works/Confirm legacy pairing, SMP_FLAG_MITM_AUTH stays clear
and the resulting STK should remain unauthenticated even if the local
side requested HIGH security. Use the established MITM state when
storing the responder STK so the key metadata matches the pairing result.
This also keeps the legacy path aligned with the Secure Connections code,
which already treats JUST_WORKS/JUST_CFM as unauthenticated. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: libertas: fix WARNING in usb_tx_block
The function usb_tx_block() submits cardp->tx_urb without ensuring that
any previous transmission on this URB has completed. If a second call
occurs while the URB is still active (e.g. during rapid firmware loading),
usb_submit_urb() detects the active state and triggers a warning:
'URB submitted while active'.
Fix this by enforcing serialization: call usb_kill_urb() before
submitting the new request. This ensures the URB is idle and safe to reuse. |
| Tanium addressed an information disclosure vulnerability in Threat Response. |
