| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: soc-compress: Reposition and add pcm_mutex
If panic_on_warn is set and compress stream(DPCM) is started,
then kernel panic occurred because card->pcm_mutex isn't held appropriately.
In the following functions, warning were issued at this line
"snd_soc_dpcm_mutex_assert_held".
static int dpcm_be_connect(struct snd_soc_pcm_runtime *fe,
struct snd_soc_pcm_runtime *be, int stream)
{
...
snd_soc_dpcm_mutex_assert_held(fe);
...
}
void dpcm_be_disconnect(struct snd_soc_pcm_runtime *fe, int stream)
{
...
snd_soc_dpcm_mutex_assert_held(fe);
...
}
void snd_soc_runtime_action(struct snd_soc_pcm_runtime *rtd,
int stream, int action)
{
...
snd_soc_dpcm_mutex_assert_held(rtd);
...
}
int dpcm_dapm_stream_event(struct snd_soc_pcm_runtime *fe, int dir,
int event)
{
...
snd_soc_dpcm_mutex_assert_held(fe);
...
}
These functions are called by soc_compr_set_params_fe, soc_compr_open_fe
and soc_compr_free_fe
without pcm_mutex locking. And this is call stack.
[ 414.527841][ T2179] pc : dpcm_process_paths+0x5a4/0x750
[ 414.527848][ T2179] lr : dpcm_process_paths+0x37c/0x750
[ 414.527945][ T2179] Call trace:
[ 414.527949][ T2179] dpcm_process_paths+0x5a4/0x750
[ 414.527955][ T2179] soc_compr_open_fe+0xb0/0x2cc
[ 414.527972][ T2179] snd_compr_open+0x180/0x248
[ 414.527981][ T2179] snd_open+0x15c/0x194
[ 414.528003][ T2179] chrdev_open+0x1b0/0x220
[ 414.528023][ T2179] do_dentry_open+0x30c/0x594
[ 414.528045][ T2179] vfs_open+0x34/0x44
[ 414.528053][ T2179] path_openat+0x914/0xb08
[ 414.528062][ T2179] do_filp_open+0xc0/0x170
[ 414.528068][ T2179] do_sys_openat2+0x94/0x18c
[ 414.528076][ T2179] __arm64_sys_openat+0x78/0xa4
[ 414.528084][ T2179] invoke_syscall+0x48/0x10c
[ 414.528094][ T2179] el0_svc_common+0xbc/0x104
[ 414.528099][ T2179] do_el0_svc+0x34/0xd8
[ 414.528103][ T2179] el0_svc+0x34/0xc4
[ 414.528125][ T2179] el0t_64_sync_handler+0x8c/0xfc
[ 414.528133][ T2179] el0t_64_sync+0x1a0/0x1a4
[ 414.528142][ T2179] Kernel panic - not syncing: panic_on_warn set ...
So, I reposition and add pcm_mutex to resolve lockdep error. |
| In the Linux kernel, the following vulnerability has been resolved:
net: stmmac: Correctly handle Rx checksum offload errors
The stmmac_rx function would previously set skb->ip_summed to
CHECKSUM_UNNECESSARY if hardware checksum offload (CoE) was enabled
and the packet was of a known IP ethertype.
However, this logic failed to check if the hardware had actually
reported a checksum error. The hardware status, indicating a header or
payload checksum failure, was being ignored at this stage. This could
cause corrupt packets to be passed up the network stack as valid.
This patch corrects the logic by checking the `csum_none` status flag,
which is set when the hardware reports a checksum error. If this flag
is set, skb->ip_summed is now correctly set to CHECKSUM_NONE,
ensuring the kernel's network stack will perform its own validation and
properly handle the corrupt packet. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/gpusvm: fix hmm_pfn_to_map_order() usage
Handle the case where the hmm range partially covers a huge page (like
2M), otherwise we can potentially end up doing something nasty like
mapping memory which is outside the range, and maybe not even mapped by
the mm. Fix is based on the xe userptr code, which in a future patch
will directly use gpusvm, so needs alignment here.
v2:
- Add kernel-doc (Matt B)
- s/fls/ilog2/ (Thomas) |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: Shutdown FW DMA in bnxt_shutdown()
The netif_close() call in bnxt_shutdown() only stops packet DMA. There
may be FW DMA for trace logging (recently added) that will continue. If
we kexec to a new kernel, the DMA will corrupt memory in the new kernel.
Add bnxt_hwrm_func_drv_unrgtr() to unregister the driver from the FW.
This will stop the FW DMA. In case the call fails, call pcie_flr() to
reset the function and stop the DMA. |
| In the Linux kernel, the following vulnerability has been resolved:
perf tool x86: Fix perf_env memory leak
Found by leak sanitizer:
```
==1632594==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 21 byte(s) in 1 object(s) allocated from:
#0 0x7f2953a7077b in __interceptor_strdup ../../../../src/libsanitizer/asan/asan_interceptors.cpp:439
#1 0x556701d6fbbf in perf_env__read_cpuid util/env.c:369
#2 0x556701d70589 in perf_env__cpuid util/env.c:465
#3 0x55670204bba2 in x86__is_amd_cpu arch/x86/util/env.c:14
#4 0x5567020487a2 in arch__post_evsel_config arch/x86/util/evsel.c:83
#5 0x556701d8f78b in evsel__config util/evsel.c:1366
#6 0x556701ef5872 in evlist__config util/record.c:108
#7 0x556701cd6bcd in test__PERF_RECORD tests/perf-record.c:112
#8 0x556701cacd07 in run_test tests/builtin-test.c:236
#9 0x556701cacfac in test_and_print tests/builtin-test.c:265
#10 0x556701cadddb in __cmd_test tests/builtin-test.c:402
#11 0x556701caf2aa in cmd_test tests/builtin-test.c:559
#12 0x556701d3b557 in run_builtin tools/perf/perf.c:323
#13 0x556701d3bac8 in handle_internal_command tools/perf/perf.c:377
#14 0x556701d3be90 in run_argv tools/perf/perf.c:421
#15 0x556701d3c3f8 in main tools/perf/perf.c:537
#16 0x7f2952a46189 in __libc_start_call_main ../sysdeps/nptl/libc_start_call_main.h:58
SUMMARY: AddressSanitizer: 21 byte(s) leaked in 1 allocation(s).
``` |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Zeroing allocated object from slab in bpf memory allocator
Currently the freed element in bpf memory allocator may be immediately
reused, for htab map the reuse will reinitialize special fields in map
value (e.g., bpf_spin_lock), but lookup procedure may still access
these special fields, and it may lead to hard-lockup as shown below:
NMI backtrace for cpu 16
CPU: 16 PID: 2574 Comm: htab.bin Tainted: G L 6.1.0+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
RIP: 0010:queued_spin_lock_slowpath+0x283/0x2c0
......
Call Trace:
<TASK>
copy_map_value_locked+0xb7/0x170
bpf_map_copy_value+0x113/0x3c0
__sys_bpf+0x1c67/0x2780
__x64_sys_bpf+0x1c/0x20
do_syscall_64+0x30/0x60
entry_SYSCALL_64_after_hwframe+0x46/0xb0
......
</TASK>
For htab map, just like the preallocated case, these is no need to
initialize these special fields in map value again once these fields
have been initialized. For preallocated htab map, these fields are
initialized through __GFP_ZERO in bpf_map_area_alloc(), so do the
similar thing for non-preallocated htab in bpf memory allocator. And
there is no need to use __GFP_ZERO for per-cpu bpf memory allocator,
because __alloc_percpu_gfp() does it implicitly. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: set generation before calling btrfs_clean_tree_block in btrfs_init_new_buffer
syzbot is reporting uninit-value in btrfs_clean_tree_block() [1], for
commit bc877d285ca3dba2 ("btrfs: Deduplicate extent_buffer init code")
missed that btrfs_set_header_generation() in btrfs_init_new_buffer() must
not be moved to after clean_tree_block() because clean_tree_block() is
calling btrfs_header_generation() since commit 55c69072d6bd5be1 ("Btrfs:
Fix extent_buffer usage when nodesize != leafsize").
Since memzero_extent_buffer() will reset "struct btrfs_header" part, we
can't move btrfs_set_header_generation() to before memzero_extent_buffer().
Just re-add btrfs_set_header_generation() before btrfs_clean_tree_block(). |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix deadlock due to mbcache entry corruption
When manipulating xattr blocks, we can deadlock infinitely looping
inside ext4_xattr_block_set() where we constantly keep finding xattr
block for reuse in mbcache but we are unable to reuse it because its
reference count is too big. This happens because cache entry for the
xattr block is marked as reusable (e_reusable set) although its
reference count is too big. When this inconsistency happens, this
inconsistent state is kept indefinitely and so ext4_xattr_block_set()
keeps retrying indefinitely.
The inconsistent state is caused by non-atomic update of e_reusable bit.
e_reusable is part of a bitfield and e_reusable update can race with
update of e_referenced bit in the same bitfield resulting in loss of one
of the updates. Fix the problem by using atomic bitops instead.
This bug has been around for many years, but it became *much* easier
to hit after commit 65f8b80053a1 ("ext4: fix race when reusing xattr
blocks"). |
| In the Linux kernel, the following vulnerability has been resolved:
hwrng: geode - Fix PCI device refcount leak
for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.
If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. We add a new struct
'amd_geode_priv' to record pointer of the pci_dev and membase, and then
add missing pci_dev_put() for the normal and error path. |
| In the Linux kernel, the following vulnerability has been resolved:
vdpa_sim: fix possible memory leak in vdpasim_net_init() and vdpasim_blk_init()
Inject fault while probing module, if device_register() fails in
vdpasim_net_init() or vdpasim_blk_init(), but the refcount of kobject is
not decreased to 0, the name allocated in dev_set_name() is leaked.
Fix this by calling put_device(), so that name can be freed in
callback function kobject_cleanup().
(vdpa_sim_net)
unreferenced object 0xffff88807eebc370 (size 16):
comm "modprobe", pid 3848, jiffies 4362982860 (age 18.153s)
hex dump (first 16 bytes):
76 64 70 61 73 69 6d 5f 6e 65 74 00 6b 6b 6b a5 vdpasim_net.kkk.
backtrace:
[<ffffffff8174f19e>] __kmalloc_node_track_caller+0x4e/0x150
[<ffffffff81731d53>] kstrdup+0x33/0x60
[<ffffffff83a5d421>] kobject_set_name_vargs+0x41/0x110
[<ffffffff82d87aab>] dev_set_name+0xab/0xe0
[<ffffffff82d91a23>] device_add+0xe3/0x1a80
[<ffffffffa0270013>] 0xffffffffa0270013
[<ffffffff81001c27>] do_one_initcall+0x87/0x2e0
[<ffffffff813739cb>] do_init_module+0x1ab/0x640
[<ffffffff81379d20>] load_module+0x5d00/0x77f0
[<ffffffff8137bc40>] __do_sys_finit_module+0x110/0x1b0
[<ffffffff83c4d505>] do_syscall_64+0x35/0x80
[<ffffffff83e0006a>] entry_SYSCALL_64_after_hwframe+0x46/0xb0
(vdpa_sim_blk)
unreferenced object 0xffff8881070c1250 (size 16):
comm "modprobe", pid 6844, jiffies 4364069319 (age 17.572s)
hex dump (first 16 bytes):
76 64 70 61 73 69 6d 5f 62 6c 6b 00 6b 6b 6b a5 vdpasim_blk.kkk.
backtrace:
[<ffffffff8174f19e>] __kmalloc_node_track_caller+0x4e/0x150
[<ffffffff81731d53>] kstrdup+0x33/0x60
[<ffffffff83a5d421>] kobject_set_name_vargs+0x41/0x110
[<ffffffff82d87aab>] dev_set_name+0xab/0xe0
[<ffffffff82d91a23>] device_add+0xe3/0x1a80
[<ffffffffa0220013>] 0xffffffffa0220013
[<ffffffff81001c27>] do_one_initcall+0x87/0x2e0
[<ffffffff813739cb>] do_init_module+0x1ab/0x640
[<ffffffff81379d20>] load_module+0x5d00/0x77f0
[<ffffffff8137bc40>] __do_sys_finit_module+0x110/0x1b0
[<ffffffff83c4d505>] do_syscall_64+0x35/0x80
[<ffffffff83e0006a>] entry_SYSCALL_64_after_hwframe+0x46/0xb0 |
| In the Linux kernel, the following vulnerability has been resolved:
platform/chrome: cros_ec_ishtp: Fix UAF after unbinding driver
After unbinding the driver, another kthread `cros_ec_console_log_work`
is still accessing the device, resulting an UAF and crash.
The driver doesn't unregister the EC device in .remove() which should
shutdown sub-devices synchronously. Fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
net: hns3: using the num_tqps in the vf driver to apply for resources
Currently, hdev->htqp is allocated using hdev->num_tqps, and kinfo->tqp
is allocated using kinfo->num_tqps. However, kinfo->num_tqps is set to
min(new_tqps, hdev->num_tqps); Therefore, kinfo->num_tqps may be smaller
than hdev->num_tqps, which causes some hdev->htqp[i] to remain
uninitialized in hclgevf_knic_setup().
Thus, this patch allocates hdev->htqp and kinfo->tqp using hdev->num_tqps,
ensuring that the lengths of hdev->htqp and kinfo->tqp are consistent
and that all elements are properly initialized. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSv4: Fix a credential leak in _nfs4_discover_trunking() |
| In the Linux kernel, the following vulnerability has been resolved:
iomap: adjust read range correctly for non-block-aligned positions
iomap_adjust_read_range() assumes that the position and length passed in
are block-aligned. This is not always the case however, as shown in the
syzbot generated case for erofs. This causes too many bytes to be
skipped for uptodate blocks, which results in returning the incorrect
position and length to read in. If all the blocks are uptodate, this
underflows length and returns a position beyond the folio.
Fix the calculation to also take into account the block offset when
calculating how many bytes can be skipped for uptodate blocks. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/sev: Make enc_dec_hypercall() accept a size instead of npages
enc_dec_hypercall() accepted a page count instead of a size, which
forced its callers to round up. As a result, non-page aligned
vaddrs caused pages to be spuriously marked as decrypted via the
encryption status hypercall, which in turn caused consistent
corruption of pages during live migration. Live migration requires
accurate encryption status information to avoid migrating pages
from the wrong perspective. |
| In the Linux kernel, the following vulnerability has been resolved:
thermal: of: fix double-free on unregistration
Since commit 3d439b1a2ad3 ("thermal/core: Alloc-copy-free the thermal
zone parameters structure"), thermal_zone_device_register() allocates
a copy of the tzp argument and frees it when unregistering, so
thermal_of_zone_register() now ends up leaking its original tzp and
double-freeing the tzp copy. Fix this by locating tzp on stack instead. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: r8712: Fix memory leak in _r8712_init_xmit_priv()
In the above mentioned routine, memory is allocated in several places.
If the first succeeds and a later one fails, the routine will leak memory.
This patch fixes commit 2865d42c78a9 ("staging: r8712u: Add the new driver
to the mainline kernel"). A potential memory leak in
r8712_xmit_resource_alloc() is also addressed. |
| In the Linux kernel, the following vulnerability has been resolved:
sfc: fix crash when reading stats while NIC is resetting
efx_net_stats() (.ndo_get_stats64) can be called during an ethtool
selftest, during which time nic_data->mc_stats is NULL as the NIC has
been fini'd. In this case do not attempt to fetch the latest stats
from the hardware, else we will crash on a NULL dereference:
BUG: kernel NULL pointer dereference, address: 0000000000000038
RIP efx_nic_update_stats
abridged calltrace:
efx_ef10_update_stats_pf
efx_net_stats
dev_get_stats
dev_seq_printf_stats
Skipping the read is safe, we will simply give out stale stats.
To ensure that the free in efx_ef10_fini_nic() does not race against
efx_ef10_update_stats_pf(), which could cause a TOCTTOU bug, take the
efx->stats_lock in fini_nic (it is already held across update_stats). |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/core: Fix GID entry ref leak when create_ah fails
If AH create request fails, release sgid_attr to avoid GID entry
referrence leak reported while releasing GID table |
| In the Linux kernel, the following vulnerability has been resolved:
udplite: Fix NULL pointer dereference in __sk_mem_raise_allocated().
syzbot reported [0] a null-ptr-deref in sk_get_rmem0() while using
IPPROTO_UDPLITE (0x88):
14:25:52 executing program 1:
r0 = socket$inet6(0xa, 0x80002, 0x88)
We had a similar report [1] for probably sk_memory_allocated_add()
in __sk_mem_raise_allocated(), and commit c915fe13cbaa ("udplite: fix
NULL pointer dereference") fixed it by setting .memory_allocated for
udplite_prot and udplitev6_prot.
To fix the variant, we need to set either .sysctl_wmem_offset or
.sysctl_rmem.
Now UDP and UDPLITE share the same value for .memory_allocated, so we
use the same .sysctl_wmem_offset for UDP and UDPLITE.
[0]:
general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 0 PID: 6829 Comm: syz-executor.1 Not tainted 6.4.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/28/2023
RIP: 0010:sk_get_rmem0 include/net/sock.h:2907 [inline]
RIP: 0010:__sk_mem_raise_allocated+0x806/0x17a0 net/core/sock.c:3006
Code: c1 ea 03 80 3c 02 00 0f 85 23 0f 00 00 48 8b 44 24 08 48 8b 98 38 01 00 00 48 b8 00 00 00 00 00 fc ff df 48 89 da 48 c1 ea 03 <0f> b6 14 02 48 89 d8 83 e0 07 83 c0 03 38 d0 0f 8d 6f 0a 00 00 8b
RSP: 0018:ffffc90005d7f450 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffffc90004d92000
RDX: 0000000000000000 RSI: ffffffff88066482 RDI: ffffffff8e2ccbb8
RBP: ffff8880173f7000 R08: 0000000000000005 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000030000
R13: 0000000000000001 R14: 0000000000000340 R15: 0000000000000001
FS: 0000000000000000(0000) GS:ffff8880b9800000(0063) knlGS:00000000f7f1cb40
CS: 0010 DS: 002b ES: 002b CR0: 0000000080050033
CR2: 000000002e82f000 CR3: 0000000034ff0000 CR4: 00000000003506f0
Call Trace:
<TASK>
__sk_mem_schedule+0x6c/0xe0 net/core/sock.c:3077
udp_rmem_schedule net/ipv4/udp.c:1539 [inline]
__udp_enqueue_schedule_skb+0x776/0xb30 net/ipv4/udp.c:1581
__udpv6_queue_rcv_skb net/ipv6/udp.c:666 [inline]
udpv6_queue_rcv_one_skb+0xc39/0x16c0 net/ipv6/udp.c:775
udpv6_queue_rcv_skb+0x194/0xa10 net/ipv6/udp.c:793
__udp6_lib_mcast_deliver net/ipv6/udp.c:906 [inline]
__udp6_lib_rcv+0x1bda/0x2bd0 net/ipv6/udp.c:1013
ip6_protocol_deliver_rcu+0x2e7/0x1250 net/ipv6/ip6_input.c:437
ip6_input_finish+0x150/0x2f0 net/ipv6/ip6_input.c:482
NF_HOOK include/linux/netfilter.h:303 [inline]
NF_HOOK include/linux/netfilter.h:297 [inline]
ip6_input+0xa0/0xd0 net/ipv6/ip6_input.c:491
ip6_mc_input+0x40b/0xf50 net/ipv6/ip6_input.c:585
dst_input include/net/dst.h:468 [inline]
ip6_rcv_finish net/ipv6/ip6_input.c:79 [inline]
NF_HOOK include/linux/netfilter.h:303 [inline]
NF_HOOK include/linux/netfilter.h:297 [inline]
ipv6_rcv+0x250/0x380 net/ipv6/ip6_input.c:309
__netif_receive_skb_one_core+0x114/0x180 net/core/dev.c:5491
__netif_receive_skb+0x1f/0x1c0 net/core/dev.c:5605
netif_receive_skb_internal net/core/dev.c:5691 [inline]
netif_receive_skb+0x133/0x7a0 net/core/dev.c:5750
tun_rx_batched+0x4b3/0x7a0 drivers/net/tun.c:1553
tun_get_user+0x2452/0x39c0 drivers/net/tun.c:1989
tun_chr_write_iter+0xdf/0x200 drivers/net/tun.c:2035
call_write_iter include/linux/fs.h:1868 [inline]
new_sync_write fs/read_write.c:491 [inline]
vfs_write+0x945/0xd50 fs/read_write.c:584
ksys_write+0x12b/0x250 fs/read_write.c:637
do_syscall_32_irqs_on arch/x86/entry/common.c:112 [inline]
__do_fast_syscall_32+0x65/0xf0 arch/x86/entry/common.c:178
do_fast_syscall_32+0x33/0x70 arch/x86/entry/common.c:203
entry_SYSENTER_compat_after_hwframe+0x70/0x82
RIP: 0023:0xf7f21579
Code: b8 01 10 06 03 74 b4 01 10 07 03 74 b0 01 10 08 03 74 d8 01 00 00 00 00 00 00 00 00 00 00 00 00 00 51 52 55 89 e5 0f 34 cd 80 <5d> 5a 59 c3 90 90 90 90 8d b4 26 00 00 00 00 8d b4 26 00 00 00 00
---truncated--- |
