| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: compress: fix to call f2fs_wait_on_page_writeback() in f2fs_write_raw_pages()
BUG_ON() will be triggered when writing files concurrently,
because the same page is writtenback multiple times.
1597 void folio_end_writeback(struct folio *folio)
1598 {
......
1618 if (!__folio_end_writeback(folio))
1619 BUG();
......
1625 }
kernel BUG at mm/filemap.c:1619!
Call Trace:
<TASK>
f2fs_write_end_io+0x1a0/0x370
blk_update_request+0x6c/0x410
blk_mq_end_request+0x15/0x130
blk_complete_reqs+0x3c/0x50
__do_softirq+0xb8/0x29b
? sort_range+0x20/0x20
run_ksoftirqd+0x19/0x20
smpboot_thread_fn+0x10b/0x1d0
kthread+0xde/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x22/0x30
</TASK>
Below is the concurrency scenario:
[Process A] [Process B] [Process C]
f2fs_write_raw_pages()
- redirty_page_for_writepage()
- unlock page()
f2fs_do_write_data_page()
- lock_page()
- clear_page_dirty_for_io()
- set_page_writeback() [1st writeback]
.....
- unlock page()
generic_perform_write()
- f2fs_write_begin()
- wait_for_stable_page()
- f2fs_write_end()
- set_page_dirty()
- lock_page()
- f2fs_do_write_data_page()
- set_page_writeback() [2st writeback]
This problem was introduced by the previous commit 7377e853967b ("f2fs:
compress: fix potential deadlock of compress file"). All pagelocks were
released in f2fs_write_raw_pages(), but whether the page was
in the writeback state was ignored in the subsequent writing process.
Let's fix it by waiting for the page to writeback before writing. |
| In the Linux kernel, the following vulnerability has been resolved:
media: dvb-usb-v2: gl861: Fix null-ptr-deref in gl861_i2c_master_xfer
In gl861_i2c_master_xfer, msg is controlled by user. When msg[i].buf
is null and msg[i].len is zero, former checks on msg[i].buf would be
passed. Malicious data finally reach gl861_i2c_master_xfer. If accessing
msg[i].buf[0] without sanity check, null ptr deref would happen.
We add check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd769a
("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()") |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: realtek: fix out-of-bounds access
The probe function sets priv->chip_data to (void *)priv + sizeof(*priv)
with the expectation that priv has enough trailing space.
However, only realtek-smi actually allocated this chip_data space.
Do likewise in realtek-mdio to fix out-of-bounds accesses.
These accesses likely went unnoticed so far, because of an (unused)
buf[4096] member in struct realtek_priv, which caused kmalloc to
round up the allocated buffer to a big enough size, so nothing of
value was overwritten. With a different allocator (like in the barebox
bootloader port of the driver) or with KASAN, the memory corruption
becomes quickly apparent. |
| In the Linux kernel, the following vulnerability has been resolved:
ipmi:ssif: Fix a memory leak when scanning for an adapter
The adapter scan ssif_info_find() sets info->adapter_name if the adapter
info came from SMBIOS, as it's not set in that case. However, this
function can be called more than once, and it will leak the adapter name
if it had already been set. So check for NULL before setting it. |
| In the Linux kernel, the following vulnerability has been resolved:
m68k: Only force 030 bus error if PC not in exception table
__get_kernel_nofault() does copy data in supervisor mode when
forcing a task backtrace log through /proc/sysrq_trigger.
This is expected cause a bus error exception on e.g. NULL
pointer dereferencing when logging a kernel task has no
workqueue associated. This bus error ought to be ignored.
Our 030 bus error handler is ill equipped to deal with this:
Whenever ssw indicates a kernel mode access on a data fault,
we don't even attempt to handle the fault and instead always
send a SEGV signal (or panic). As a result, the check
for exception handling at the fault PC (buried in
send_sig_fault() which gets called from do_page_fault()
eventually) is never used.
In contrast, both 040 and 060 access error handlers do not
care whether a fault happened on supervisor mode access,
and will call do_page_fault() on those, ultimately honoring
the exception table.
Add a check in bus_error030 to call do_page_fault() in case
we do have an entry for the fault PC in our exception table.
I had attempted a fix for this earlier in 2019 that did rely
on testing pagefault_disabled() (see link below) to achieve
the same thing, but this patch should be more generic.
Tested on 030 Atari Falcon. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix invalid free tracking in ext4_xattr_move_to_block()
In ext4_xattr_move_to_block(), the value of the extended attribute
which we need to move to an external block may be allocated by
kvmalloc() if the value is stored in an external inode. So at the end
of the function the code tried to check if this was the case by
testing entry->e_value_inum.
However, at this point, the pointer to the xattr entry is no longer
valid, because it was removed from the original location where it had
been stored. So we could end up calling kvfree() on a pointer which
was not allocated by kvmalloc(); or we could also potentially leak
memory by not freeing the buffer when it should be freed. Fix this by
storing whether it should be freed in a separate variable. |
| In the Linux kernel, the following vulnerability has been resolved:
soc: mediatek: mtk-svs: Enable the IRQ later
If the system does not come from reset (like when is booted via
kexec()), the peripheral might triger an IRQ before the data structures
are initialised.
[ 0.227710] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000f08
[ 0.227913] Call trace:
[ 0.227918] svs_isr+0x8c/0x538 |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/irdma: Fix memory leak of PBLE objects
On rmmod of irdma, the PBLE object memory is not being freed. PBLE object
memory are not statically pre-allocated at function initialization time
unlike other HMC objects. PBLEs objects and the Segment Descriptors (SD)
for it can be dynamically allocated during scale up and SD's remain
allocated till function deinitialization.
Fix this leak by adding IRDMA_HMC_IW_PBLE to the iw_hmc_obj_types[] table
and skip pbles in irdma_create_hmc_obj but not in irdma_del_hmc_objects(). |
| In the Linux kernel, the following vulnerability has been resolved:
ubifs: Fix memleak when insert_old_idx() failed
Following process will cause a memleak for copied up znode:
dirty_cow_znode
zn = copy_znode(c, znode);
err = insert_old_idx(c, zbr->lnum, zbr->offs);
if (unlikely(err))
return ERR_PTR(err); // No one refers to zn.
Fetch a reproducer in [Link].
Function copy_znode() is split into 2 parts: resource allocation
and znode replacement, insert_old_idx() is split in similar way,
so resource cleanup could be done in error handling path without
corrupting metadata(mem & disk).
It's okay that old index inserting is put behind of add_idx_dirt(),
old index is used in layout_leb_in_gaps(), so the two processes do
not depend on each other. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/bnxt_re: Prevent handling any completions after qp destroy
HW may generate completions that indicates QP is destroyed.
Driver should not be scheduling any more completion handlers
for this QP, after the QP is destroyed. Since CQs are active
during the QP destroy, driver may still schedule completion
handlers. This can cause a race where the destroy_cq and poll_cq
running simultaneously.
Snippet of kernel panic while doing bnxt_re driver load unload in loop.
This indicates a poll after the CQ is freed.
[77786.481636] Call Trace:
[77786.481640] <TASK>
[77786.481644] bnxt_re_poll_cq+0x14a/0x620 [bnxt_re]
[77786.481658] ? kvm_clock_read+0x14/0x30
[77786.481693] __ib_process_cq+0x57/0x190 [ib_core]
[77786.481728] ib_cq_poll_work+0x26/0x80 [ib_core]
[77786.481761] process_one_work+0x1e5/0x3f0
[77786.481768] worker_thread+0x50/0x3a0
[77786.481785] ? __pfx_worker_thread+0x10/0x10
[77786.481790] kthread+0xe2/0x110
[77786.481794] ? __pfx_kthread+0x10/0x10
[77786.481797] ret_from_fork+0x2c/0x50
To avoid this, complete all completion handlers before returning the
destroy QP. If free_cq is called soon after destroy_qp, IB stack
will cancel the CQ work before invoking the destroy_cq verb and
this will prevent any race mentioned. |
| In the Linux kernel, the following vulnerability has been resolved:
audit: fix possible soft lockup in __audit_inode_child()
Tracefs or debugfs maybe cause hundreds to thousands of PATH records,
too many PATH records maybe cause soft lockup.
For example:
1. CONFIG_KASAN=y && CONFIG_PREEMPTION=n
2. auditctl -a exit,always -S open -k key
3. sysctl -w kernel.watchdog_thresh=5
4. mkdir /sys/kernel/debug/tracing/instances/test
There may be a soft lockup as follows:
watchdog: BUG: soft lockup - CPU#45 stuck for 7s! [mkdir:15498]
Kernel panic - not syncing: softlockup: hung tasks
Call trace:
dump_backtrace+0x0/0x30c
show_stack+0x20/0x30
dump_stack+0x11c/0x174
panic+0x27c/0x494
watchdog_timer_fn+0x2bc/0x390
__run_hrtimer+0x148/0x4fc
__hrtimer_run_queues+0x154/0x210
hrtimer_interrupt+0x2c4/0x760
arch_timer_handler_phys+0x48/0x60
handle_percpu_devid_irq+0xe0/0x340
__handle_domain_irq+0xbc/0x130
gic_handle_irq+0x78/0x460
el1_irq+0xb8/0x140
__audit_inode_child+0x240/0x7bc
tracefs_create_file+0x1b8/0x2a0
trace_create_file+0x18/0x50
event_create_dir+0x204/0x30c
__trace_add_new_event+0xac/0x100
event_trace_add_tracer+0xa0/0x130
trace_array_create_dir+0x60/0x140
trace_array_create+0x1e0/0x370
instance_mkdir+0x90/0xd0
tracefs_syscall_mkdir+0x68/0xa0
vfs_mkdir+0x21c/0x34c
do_mkdirat+0x1b4/0x1d4
__arm64_sys_mkdirat+0x4c/0x60
el0_svc_common.constprop.0+0xa8/0x240
do_el0_svc+0x8c/0xc0
el0_svc+0x20/0x30
el0_sync_handler+0xb0/0xb4
el0_sync+0x160/0x180
Therefore, we add cond_resched() to __audit_inode_child() to fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
spmi: Add a check for remove callback when removing a SPMI driver
When removing a SPMI driver, there can be a crash due to NULL pointer
dereference if it does not have a remove callback defined. This is
one such call trace observed when removing the QCOM SPMI PMIC driver:
dump_backtrace.cfi_jt+0x0/0x8
dump_stack_lvl+0xd8/0x16c
panic+0x188/0x498
__cfi_slowpath+0x0/0x214
__cfi_slowpath+0x1dc/0x214
spmi_drv_remove+0x16c/0x1e0
device_release_driver_internal+0x468/0x79c
driver_detach+0x11c/0x1a0
bus_remove_driver+0xc4/0x124
driver_unregister+0x58/0x84
cleanup_module+0x1c/0xc24 [qcom_spmi_pmic]
__do_sys_delete_module+0x3ec/0x53c
__arm64_sys_delete_module+0x18/0x28
el0_svc_common+0xdc/0x294
el0_svc+0x38/0x9c
el0_sync_handler+0x8c/0xf0
el0_sync+0x1b4/0x1c0
If a driver has all its resources allocated through devm_() APIs and
does not need any other explicit cleanup, it would not require a
remove callback to be defined. Hence, add a check for remove callback
presence before calling it when removing a SPMI driver. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix registration of 6Ghz-only phy without the full channel range
Because of what seems to be a typo, a 6Ghz-only phy for which the BDF
does not allow the 7115Mhz channel will fail to register:
WARNING: CPU: 2 PID: 106 at net/wireless/core.c:907 wiphy_register+0x914/0x954
Modules linked in: ath11k_pci sbsa_gwdt
CPU: 2 PID: 106 Comm: kworker/u8:5 Not tainted 6.3.0-rc7-next-20230418-00549-g1e096a17625a-dirty #9
Hardware name: Freebox V7R Board (DT)
Workqueue: ath11k_qmi_driver_event ath11k_qmi_driver_event_work
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : wiphy_register+0x914/0x954
lr : ieee80211_register_hw+0x67c/0xc10
sp : ffffff800b123aa0
x29: ffffff800b123aa0 x28: 0000000000000000 x27: 0000000000000000
x26: 0000000000000000 x25: 0000000000000006 x24: ffffffc008d51418
x23: ffffffc008cb0838 x22: ffffff80176c2460 x21: 0000000000000168
x20: ffffff80176c0000 x19: ffffff80176c03e0 x18: 0000000000000014
x17: 00000000cbef338c x16: 00000000d2a26f21 x15: 00000000ad6bb85f
x14: 0000000000000020 x13: 0000000000000020 x12: 00000000ffffffbd
x11: 0000000000000208 x10: 00000000fffffdf7 x9 : ffffffc009394718
x8 : ffffff80176c0528 x7 : 000000007fffffff x6 : 0000000000000006
x5 : 0000000000000005 x4 : ffffff800b304284 x3 : ffffff800b304284
x2 : ffffff800b304d98 x1 : 0000000000000000 x0 : 0000000000000000
Call trace:
wiphy_register+0x914/0x954
ieee80211_register_hw+0x67c/0xc10
ath11k_mac_register+0x7c4/0xe10
ath11k_core_qmi_firmware_ready+0x1f4/0x570
ath11k_qmi_driver_event_work+0x198/0x590
process_one_work+0x1b8/0x328
worker_thread+0x6c/0x414
kthread+0x100/0x104
ret_from_fork+0x10/0x20
---[ end trace 0000000000000000 ]---
ath11k_pci 0002:01:00.0: ieee80211 registration failed: -22
ath11k_pci 0002:01:00.0: failed register the radio with mac80211: -22
ath11k_pci 0002:01:00.0: failed to create pdev core: -22 |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring: fix memory leak when removing provided buffers
When removing provided buffers, io_buffer structs are not being disposed
of, leading to a memory leak. They can't be freed individually, because
they are allocated in page-sized groups. They need to be added to some
free list instead, such as io_buffers_cache. All callers already hold
the lock protecting it, apart from when destroying buffers, so had to
extend the lock there. |
| In the Linux kernel, the following vulnerability has been resolved:
ice: fix wrong fallback logic for FDIR
When adding a FDIR filter, if ice_vc_fdir_set_irq_ctx returns failure,
the inserted fdir entry will not be removed and if ice_vc_fdir_write_fltr
returns failure, the fdir context info for irq handler will not be cleared
which may lead to inconsistent or memory leak issue. This patch refines
failure cases to resolve this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
can: j1939: j1939_tp_tx_dat_new(): fix out-of-bounds memory access
In the j1939_tp_tx_dat_new() function, an out-of-bounds memory access
could occur during the memcpy() operation if the size of skb->cb is
larger than the size of struct j1939_sk_buff_cb. This is because the
memcpy() operation uses the size of skb->cb, leading to a read beyond
the struct j1939_sk_buff_cb.
Updated the memcpy() operation to use the size of struct
j1939_sk_buff_cb instead of the size of skb->cb. This ensures that the
memcpy() operation only reads the memory within the bounds of struct
j1939_sk_buff_cb, preventing out-of-bounds memory access.
Additionally, add a BUILD_BUG_ON() to check that the size of skb->cb
is greater than or equal to the size of struct j1939_sk_buff_cb. This
ensures that the skb->cb buffer is large enough to hold the
j1939_sk_buff_cb structure.
[mkl: rephrase commit message] |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: fix underflow in chain reference counter
Set element addition error path decrements reference counter on chains
twice: once on element release and again via nft_data_release().
Then, d6b478666ffa ("netfilter: nf_tables: fix underflow in object
reference counter") incorrectly fixed this by removing the stateful
object reference count decrement.
Restore the stateful object decrement as in b91d90368837 ("netfilter:
nf_tables: fix leaking object reference count") and let
nft_data_release() decrement the chain reference counter, so this is
done only once. |
| In the Linux kernel, the following vulnerability has been resolved:
iommufd: Make sure to zero vfio_iommu_type1_info before copying to user
Missed a zero initialization here. Most of the struct is filled with
a copy_from_user(), however minsz for that copy is smaller than the
actual struct by 8 bytes, thus we don't fill the padding. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: Fix the error "trying to register non-static key in rxe_cleanup_task"
In the function rxe_create_qp(), rxe_qp_from_init() is called to
initialize qp, internally things like rxe_init_task are not setup until
rxe_qp_init_req().
If an error occurred before this point then the unwind will call
rxe_cleanup() and eventually to rxe_qp_do_cleanup()/rxe_cleanup_task()
which will oops when trying to access the uninitialized spinlock.
If rxe_init_task is not executed, rxe_cleanup_task will not be called. |
| In the Linux kernel, the following vulnerability has been resolved:
opp: Fix use-after-free in lazy_opp_tables after probe deferral
When dev_pm_opp_of_find_icc_paths() in _allocate_opp_table() returns
-EPROBE_DEFER, the opp_table is freed again, to wait until all the
interconnect paths are available.
However, if the OPP table is using required-opps then it may already
have been added to the global lazy_opp_tables list. The error path
does not remove the opp_table from the list again.
This can cause crashes later when the provider of the required-opps
is added, since we will iterate over OPP tables that have already been
freed. E.g.:
Unable to handle kernel NULL pointer dereference when read
CPU: 0 PID: 7 Comm: kworker/0:0 Not tainted 6.4.0-rc3
PC is at _of_add_opp_table_v2 (include/linux/of.h:949
drivers/opp/of.c:98 drivers/opp/of.c:344 drivers/opp/of.c:404
drivers/opp/of.c:1032) -> lazy_link_required_opp_table()
Fix this by calling _of_clear_opp_table() to remove the opp_table from
the list and clear other allocated resources. While at it, also add the
missing mutex_destroy() calls in the error path. |
