| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/rxe: Fix race in do_task() when draining
When do_task() exhausts its iteration budget (!ret), it sets the state
to TASK_STATE_IDLE to reschedule, without a secondary check on the
current task->state. This can overwrite the TASK_STATE_DRAINING state
set by a concurrent call to rxe_cleanup_task() or rxe_disable_task().
While state changes are protected by a spinlock, both rxe_cleanup_task()
and rxe_disable_task() release the lock while waiting for the task to
finish draining in the while(!is_done(task)) loop. The race occurs if
do_task() hits its iteration limit and acquires the lock in this window.
The cleanup logic may then proceed while the task incorrectly
reschedules itself, leading to a potential use-after-free.
This bug was introduced during the migration from tasklets to workqueues,
where the special handling for the draining case was lost.
Fix this by restoring the original pre-migration behavior. If the state is
TASK_STATE_DRAINING when iterations are exhausted, set cont to 1 to
force a new loop iteration. This allows the task to finish its work, so
that a subsequent iteration can reach the switch statement and correctly
transition the state to TASK_STATE_DRAINED, stopping the task as intended. |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: use proper req destructor for IPv6
Before, only the destructor from TCP request sock in IPv4 was called
even if the subflow was IPv6.
It is important to use the right destructor to avoid memory leaks with
some advanced IPv6 features, e.g. when the request socks contain
specific IPv6 options. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: wusb3801: fix fwnode refcount leak in wusb3801_probe()
I got the following report while doing fault injection test:
OF: ERROR: memory leak, expected refcount 1 instead of 4,
of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /i2c/tcpc@60/connector
If wusb3801_hw_init() fails, fwnode_handle_put() needs be called to
avoid refcount leak. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: lpfc: Fix memory leak in lpfc_create_port()
Commit 5e633302ace1 ("scsi: lpfc: vmid: Add support for VMID in mailbox
command") introduced allocations for the VMID resources in
lpfc_create_port() after the call to scsi_host_alloc(). Upon failure on the
VMID allocations, the new code would branch to the 'out' label, which
returns NULL without unwinding anything, thus skipping the call to
scsi_host_put().
Fix the problem by creating a separate label 'out_free_vmid' to unwind the
VMID resources and make the 'out_put_shost' label call only
scsi_host_put(), as was done before the introduction of allocations for
VMID. |
| In the Linux kernel, the following vulnerability has been resolved:
clk: tegra: Fix refcount leak in tegra114_clock_init
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak. |
| In the Linux kernel, the following vulnerability has been resolved:
SUNRPC: Don't leak netobj memory when gss_read_proxy_verf() fails |
| In the Linux kernel, the following vulnerability has been resolved:
net: hsr: avoid possible NULL deref in skb_clone()
syzbot got a crash [1] in skb_clone(), caused by a bug
in hsr_get_untagged_frame().
When/if create_stripped_skb_hsr() returns NULL, we must
not attempt to call skb_clone().
While we are at it, replace a WARN_ONCE() by netdev_warn_once().
[1]
general protection fault, probably for non-canonical address 0xdffffc000000000f: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000078-0x000000000000007f]
CPU: 1 PID: 754 Comm: syz-executor.0 Not tainted 6.0.0-syzkaller-02734-g0326074ff465 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/22/2022
RIP: 0010:skb_clone+0x108/0x3c0 net/core/skbuff.c:1641
Code: 93 02 00 00 49 83 7c 24 28 00 0f 85 e9 00 00 00 e8 5d 4a 29 fa 4c 8d 75 7e 48 b8 00 00 00 00 00 fc ff df 4c 89 f2 48 c1 ea 03 <0f> b6 04 02 4c 89 f2 83 e2 07 38 d0 7f 08 84 c0 0f 85 9e 01 00 00
RSP: 0018:ffffc90003ccf4e0 EFLAGS: 00010207
RAX: dffffc0000000000 RBX: ffffc90003ccf5f8 RCX: ffffc9000c24b000
RDX: 000000000000000f RSI: ffffffff8751cb13 RDI: 0000000000000000
RBP: 0000000000000000 R08: 00000000000000f0 R09: 0000000000000140
R10: fffffbfff181d972 R11: 0000000000000000 R12: ffff888161fc3640
R13: 0000000000000a20 R14: 000000000000007e R15: ffffffff8dc5f620
FS: 00007feb621e4700(0000) GS:ffff8880b9b00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007feb621e3ff8 CR3: 00000001643a9000 CR4: 00000000003506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
hsr_get_untagged_frame+0x4e/0x610 net/hsr/hsr_forward.c:164
hsr_forward_do net/hsr/hsr_forward.c:461 [inline]
hsr_forward_skb+0xcca/0x1d50 net/hsr/hsr_forward.c:623
hsr_handle_frame+0x588/0x7c0 net/hsr/hsr_slave.c:69
__netif_receive_skb_core+0x9fe/0x38f0 net/core/dev.c:5379
__netif_receive_skb_one_core+0xae/0x180 net/core/dev.c:5483
__netif_receive_skb+0x1f/0x1c0 net/core/dev.c:5599
netif_receive_skb_internal net/core/dev.c:5685 [inline]
netif_receive_skb+0x12f/0x8d0 net/core/dev.c:5744
tun_rx_batched+0x4ab/0x7a0 drivers/net/tun.c:1544
tun_get_user+0x2686/0x3a00 drivers/net/tun.c:1995
tun_chr_write_iter+0xdb/0x200 drivers/net/tun.c:2025
call_write_iter include/linux/fs.h:2187 [inline]
new_sync_write fs/read_write.c:491 [inline]
vfs_write+0x9e9/0xdd0 fs/read_write.c:584
ksys_write+0x127/0x250 fs/read_write.c:637
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd |
| In the Linux kernel, the following vulnerability has been resolved:
ext2: Add sanity checks for group and filesystem size
Add sanity check that filesystem size does not exceed the underlying
device size and that group size is big enough so that metadata can fit
into it. This avoid trying to mount some crafted filesystems with
extremely large group counts. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: hisilicon/zip - fix mismatch in get/set sgl_sge_nr
KASAN reported this Bug:
[17619.659757] BUG: KASAN: global-out-of-bounds in param_get_int+0x34/0x60
[17619.673193] Read of size 4 at addr fffff01332d7ed00 by task read_all/1507958
...
[17619.698934] The buggy address belongs to the variable:
[17619.708371] sgl_sge_nr+0x0/0xffffffffffffa300 [hisi_zip]
There is a mismatch in hisi_zip when get/set the variable sgl_sge_nr.
The type of sgl_sge_nr is u16, and get/set sgl_sge_nr by
param_get/set_int.
Replacing param_get/set_int to param_get/set_ushort can fix this bug. |
| In the Linux kernel, the following vulnerability has been resolved:
clk: zynqmp: Fix stack-out-of-bounds in strncpy`
"BUG: KASAN: stack-out-of-bounds in strncpy+0x30/0x68"
Linux-ATF interface is using 16 bytes of SMC payload. In case clock name is
longer than 15 bytes, string terminated NULL character will not be received
by Linux. Add explicit NULL character at last byte to fix issues when clock
name is longer.
This fixes below bug reported by KASAN:
==================================================================
BUG: KASAN: stack-out-of-bounds in strncpy+0x30/0x68
Read of size 1 at addr ffff0008c89a7410 by task swapper/0/1
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.4.0-00396-g81ef9e7-dirty #3
Hardware name: Xilinx Versal vck190 Eval board revA (QSPI) (DT)
Call trace:
dump_backtrace+0x0/0x1e8
show_stack+0x14/0x20
dump_stack+0xd4/0x108
print_address_description.isra.0+0xbc/0x37c
__kasan_report+0x144/0x198
kasan_report+0xc/0x18
__asan_load1+0x5c/0x68
strncpy+0x30/0x68
zynqmp_clock_probe+0x238/0x7b8
platform_drv_probe+0x6c/0xc8
really_probe+0x14c/0x418
driver_probe_device+0x74/0x130
__device_attach_driver+0xc4/0xe8
bus_for_each_drv+0xec/0x150
__device_attach+0x160/0x1d8
device_initial_probe+0x10/0x18
bus_probe_device+0xe0/0xf0
device_add+0x528/0x950
of_device_add+0x5c/0x80
of_platform_device_create_pdata+0x120/0x168
of_platform_bus_create+0x244/0x4e0
of_platform_populate+0x50/0xe8
zynqmp_firmware_probe+0x370/0x3a8
platform_drv_probe+0x6c/0xc8
really_probe+0x14c/0x418
driver_probe_device+0x74/0x130
device_driver_attach+0x94/0xa0
__driver_attach+0x70/0x108
bus_for_each_dev+0xe4/0x158
driver_attach+0x30/0x40
bus_add_driver+0x21c/0x2b8
driver_register+0xbc/0x1d0
__platform_driver_register+0x7c/0x88
zynqmp_firmware_driver_init+0x1c/0x24
do_one_initcall+0xa4/0x234
kernel_init_freeable+0x1b0/0x24c
kernel_init+0x10/0x110
ret_from_fork+0x10/0x18
The buggy address belongs to the page:
page:ffff0008f9be1c88 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0
raw: 0008d00000000000 ffff0008f9be1c90 ffff0008f9be1c90 0000000000000000
raw: 0000000000000000 0000000000000000 00000000ffffffff
page dumped because: kasan: bad access detected
addr ffff0008c89a7410 is located in stack of task swapper/0/1 at offset 112 in frame:
zynqmp_clock_probe+0x0/0x7b8
this frame has 3 objects:
[32, 44) 'response'
[64, 80) 'ret_payload'
[96, 112) 'name'
Memory state around the buggy address:
ffff0008c89a7300: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff0008c89a7380: 00 00 00 00 f1 f1 f1 f1 00 04 f2 f2 00 00 f2 f2
>ffff0008c89a7400: 00 00 f3 f3 00 00 00 00 00 00 00 00 00 00 00 00
^
ffff0008c89a7480: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff0008c89a7500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
================================================================== |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath9k: hif_usb: Fix use-after-free in ath9k_hif_usb_reg_in_cb()
It is possible that skb is freed in ath9k_htc_rx_msg(), then
usb_submit_urb() fails and we try to free skb again. It causes
use-after-free bug. Moreover, if alloc_skb() fails, urb->context becomes
NULL but rx_buf is not freed and there can be a memory leak.
The patch removes unnecessary nskb and makes skb processing more clear: it
is supposed that ath9k_htc_rx_msg() either frees old skb or passes its
managing to another callback function.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller. |
| In the Linux kernel, the following vulnerability has been resolved:
auxdisplay: hd44780: Fix potential memory leak in hd44780_remove()
hd44780_probe() allocates a memory chunk for hd with kzalloc() and
makes "lcd->drvdata->hd44780" point to it. When we call hd44780_remove(),
we should release all relevant memory and resource. But "lcd->drvdata
->hd44780" is not released, which will lead to a memory leak.
We should release the "lcd->drvdata->hd44780" in hd44780_remove() to fix
the memory leak bug. |
| In the Linux kernel, the following vulnerability has been resolved:
drivers: mcb: fix resource leak in mcb_probe()
When probe hook function failed in mcb_probe(), it doesn't put the device.
Compiled test only. |
| In the Linux kernel, the following vulnerability has been resolved:
security: Restrict CONFIG_ZERO_CALL_USED_REGS to gcc or clang > 15.0.6
A bad bug in clang's implementation of -fzero-call-used-regs can result
in NULL pointer dereferences (see the links above the check for more
information). Restrict CONFIG_CC_HAS_ZERO_CALL_USED_REGS to either a
supported GCC version or a clang newer than 15.0.6, which will catch
both a theoretical 15.0.7 and the upcoming 16.0.0, which will both have
the bug fixed. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: wilc1000: fix potential memory leak in wilc_mac_xmit()
The wilc_mac_xmit() returns NETDEV_TX_OK without freeing skb, add
dev_kfree_skb() to fix it. Compile tested only. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: use hdev->workqueue when queuing hdev->{cmd,ncmd}_timer works
syzbot is reporting attempt to schedule hdev->cmd_work work from system_wq
WQ into hdev->workqueue WQ which is under draining operation [1], for
commit c8efcc2589464ac7 ("workqueue: allow chained queueing during
destruction") does not allow such operation.
The check introduced by commit 877afadad2dce8aa ("Bluetooth: When HCI work
queue is drained, only queue chained work") was incomplete.
Use hdev->workqueue WQ when queuing hdev->{cmd,ncmd}_timer works because
hci_{cmd,ncmd}_timeout() calls queue_work(hdev->workqueue). Also, protect
the queuing operation with RCU read lock in order to avoid calling
queue_delayed_work() after cancel_delayed_work() completed. |
| In the Linux kernel, the following vulnerability has been resolved:
xhci: dbc: Fix memory leak in xhci_alloc_dbc()
If DbC is already in use, then the allocated memory for the xhci_dbc struct
doesn't get freed before returning NULL, which leads to a memleak. |
| In the Linux kernel, the following vulnerability has been resolved:
media: s5p-mfc: Clear workbit to handle error condition
During error on CLOSE_INSTANCE command, ctx_work_bits was not getting
cleared. During consequent mfc execution NULL pointer dereferencing of
this context led to kernel panic. This patch fixes this issue by making
sure to clear ctx_work_bits always. |
| In the Linux kernel, the following vulnerability has been resolved:
nfc: Fix potential resource leaks
nfc_get_device() take reference for the device, add missing
nfc_put_device() to release it when not need anymore.
Also fix the style warnning by use error EOPNOTSUPP instead of
ENOTSUPP. |
| In the Linux kernel, the following vulnerability has been resolved:
fsi: occ: Prevent use after free
Use get_device and put_device in the open and close functions to
make sure the device doesn't get freed while a file descriptor is
open.
Also, lock around the freeing of the device buffer and check the
buffer before using it in the submit function. |
