| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: tegra: check msg length in SMBUS block read
For SMBUS block read, do not continue to read if the message length
passed from the device is '0' or greater than the maximum allowed bytes. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath6kl: remove WARN on bad firmware input
If the firmware gives bad input, that's nothing to do with
the driver's stack at this point etc., so the WARN_ON()
doesn't add any value. Additionally, this is one of the
top syzbot reports now. Just print a message, and as an
added bonus, print the sizes too. |
| In the Linux kernel, the following vulnerability has been resolved:
ACPICA: Refuse to evaluate a method if arguments are missing
As reported in [1], a platform firmware update that increased the number
of method parameters and forgot to update a least one of its callers,
caused ACPICA to crash due to use-after-free.
Since this a result of a clear AML issue that arguably cannot be fixed
up by the interpreter (it cannot produce missing data out of thin air),
address it by making ACPICA refuse to evaluate a method if the caller
attempts to pass fewer arguments than expected to it. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: spinand: fix memory leak of ECC engine conf
Memory allocated for the ECC engine conf is not released during spinand
cleanup. Below kmemleak trace is seen for this memory leak:
unreferenced object 0xffffff80064f00e0 (size 8):
comm "swapper/0", pid 1, jiffies 4294937458
hex dump (first 8 bytes):
00 00 00 00 00 00 00 00 ........
backtrace (crc 0):
kmemleak_alloc+0x30/0x40
__kmalloc_cache_noprof+0x208/0x3c0
spinand_ondie_ecc_init_ctx+0x114/0x200
nand_ecc_init_ctx+0x70/0xa8
nanddev_ecc_engine_init+0xec/0x27c
spinand_probe+0xa2c/0x1620
spi_mem_probe+0x130/0x21c
spi_probe+0xf0/0x170
really_probe+0x17c/0x6e8
__driver_probe_device+0x17c/0x21c
driver_probe_device+0x58/0x180
__device_attach_driver+0x15c/0x1f8
bus_for_each_drv+0xec/0x150
__device_attach+0x188/0x24c
device_initial_probe+0x10/0x20
bus_probe_device+0x11c/0x160
Fix the leak by calling nanddev_ecc_engine_cleanup() inside
spinand_cleanup(). |
| In the Linux kernel, the following vulnerability has been resolved:
ACPICA: fix acpi operand cache leak in dswstate.c
ACPICA commit 987a3b5cf7175916e2a4b6ea5b8e70f830dfe732
I found an ACPI cache leak in ACPI early termination and boot continuing case.
When early termination occurs due to malicious ACPI table, Linux kernel
terminates ACPI function and continues to boot process. While kernel terminates
ACPI function, kmem_cache_destroy() reports Acpi-Operand cache leak.
Boot log of ACPI operand cache leak is as follows:
>[ 0.585957] ACPI: Added _OSI(Module Device)
>[ 0.587218] ACPI: Added _OSI(Processor Device)
>[ 0.588530] ACPI: Added _OSI(3.0 _SCP Extensions)
>[ 0.589790] ACPI: Added _OSI(Processor Aggregator Device)
>[ 0.591534] ACPI Error: Illegal I/O port address/length above 64K: C806E00000004002/0x2 (20170303/hwvalid-155)
>[ 0.594351] ACPI Exception: AE_LIMIT, Unable to initialize fixed events (20170303/evevent-88)
>[ 0.597858] ACPI: Unable to start the ACPI Interpreter
>[ 0.599162] ACPI Error: Could not remove SCI handler (20170303/evmisc-281)
>[ 0.601836] kmem_cache_destroy Acpi-Operand: Slab cache still has objects
>[ 0.603556] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.12.0-rc5 #26
>[ 0.605159] Hardware name: innotek gmb_h virtual_box/virtual_box, BIOS virtual_box 12/01/2006
>[ 0.609177] Call Trace:
>[ 0.610063] ? dump_stack+0x5c/0x81
>[ 0.611118] ? kmem_cache_destroy+0x1aa/0x1c0
>[ 0.612632] ? acpi_sleep_proc_init+0x27/0x27
>[ 0.613906] ? acpi_os_delete_cache+0xa/0x10
>[ 0.617986] ? acpi_ut_delete_caches+0x3f/0x7b
>[ 0.619293] ? acpi_terminate+0xa/0x14
>[ 0.620394] ? acpi_init+0x2af/0x34f
>[ 0.621616] ? __class_create+0x4c/0x80
>[ 0.623412] ? video_setup+0x7f/0x7f
>[ 0.624585] ? acpi_sleep_proc_init+0x27/0x27
>[ 0.625861] ? do_one_initcall+0x4e/0x1a0
>[ 0.627513] ? kernel_init_freeable+0x19e/0x21f
>[ 0.628972] ? rest_init+0x80/0x80
>[ 0.630043] ? kernel_init+0xa/0x100
>[ 0.631084] ? ret_from_fork+0x25/0x30
>[ 0.633343] vgaarb: loaded
>[ 0.635036] EDAC MC: Ver: 3.0.0
>[ 0.638601] PCI: Probing PCI hardware
>[ 0.639833] PCI host bridge to bus 0000:00
>[ 0.641031] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
> ... Continue to boot and log is omitted ...
I analyzed this memory leak in detail and found acpi_ds_obj_stack_pop_and_
delete() function miscalculated the top of the stack. acpi_ds_obj_stack_push()
function uses walk_state->operand_index for start position of the top, but
acpi_ds_obj_stack_pop_and_delete() function considers index 0 for it.
Therefore, this causes acpi operand memory leak.
This cache leak causes a security threat because an old kernel (<= 4.9) shows
memory locations of kernel functions in stack dump. Some malicious users
could use this information to neutralize kernel ASLR.
I made a patch to fix ACPI operand cache leak. |
| In the Linux kernel, the following vulnerability has been resolved:
ACPICA: fix acpi parse and parseext cache leaks
ACPICA commit 8829e70e1360c81e7a5a901b5d4f48330e021ea5
I'm Seunghun Han, and I work for National Security Research Institute of
South Korea.
I have been doing a research on ACPI and found an ACPI cache leak in ACPI
early abort cases.
Boot log of ACPI cache leak is as follows:
[ 0.352414] ACPI: Added _OSI(Module Device)
[ 0.353182] ACPI: Added _OSI(Processor Device)
[ 0.353182] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.353182] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.356028] ACPI: Unable to start the ACPI Interpreter
[ 0.356799] ACPI Error: Could not remove SCI handler (20170303/evmisc-281)
[ 0.360215] kmem_cache_destroy Acpi-State: Slab cache still has objects
[ 0.360648] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W
4.12.0-rc4-next-20170608+ #10
[ 0.361273] Hardware name: innotek gmb_h virtual_box/virtual_box, BIOS
virtual_box 12/01/2006
[ 0.361873] Call Trace:
[ 0.362243] ? dump_stack+0x5c/0x81
[ 0.362591] ? kmem_cache_destroy+0x1aa/0x1c0
[ 0.362944] ? acpi_sleep_proc_init+0x27/0x27
[ 0.363296] ? acpi_os_delete_cache+0xa/0x10
[ 0.363646] ? acpi_ut_delete_caches+0x6d/0x7b
[ 0.364000] ? acpi_terminate+0xa/0x14
[ 0.364000] ? acpi_init+0x2af/0x34f
[ 0.364000] ? __class_create+0x4c/0x80
[ 0.364000] ? video_setup+0x7f/0x7f
[ 0.364000] ? acpi_sleep_proc_init+0x27/0x27
[ 0.364000] ? do_one_initcall+0x4e/0x1a0
[ 0.364000] ? kernel_init_freeable+0x189/0x20a
[ 0.364000] ? rest_init+0xc0/0xc0
[ 0.364000] ? kernel_init+0xa/0x100
[ 0.364000] ? ret_from_fork+0x25/0x30
I analyzed this memory leak in detail. I found that “Acpi-State” cache and
“Acpi-Parse” cache were merged because the size of cache objects was same
slab cache size.
I finally found “Acpi-Parse” cache and “Acpi-parse_ext” cache were leaked
using SLAB_NEVER_MERGE flag in kmem_cache_create() function.
Real ACPI cache leak point is as follows:
[ 0.360101] ACPI: Added _OSI(Module Device)
[ 0.360101] ACPI: Added _OSI(Processor Device)
[ 0.360101] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.361043] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.364016] ACPI: Unable to start the ACPI Interpreter
[ 0.365061] ACPI Error: Could not remove SCI handler (20170303/evmisc-281)
[ 0.368174] kmem_cache_destroy Acpi-Parse: Slab cache still has objects
[ 0.369332] CPU: 1 PID: 1 Comm: swapper/0 Tainted: G W
4.12.0-rc4-next-20170608+ #8
[ 0.371256] Hardware name: innotek gmb_h virtual_box/virtual_box, BIOS
virtual_box 12/01/2006
[ 0.372000] Call Trace:
[ 0.372000] ? dump_stack+0x5c/0x81
[ 0.372000] ? kmem_cache_destroy+0x1aa/0x1c0
[ 0.372000] ? acpi_sleep_proc_init+0x27/0x27
[ 0.372000] ? acpi_os_delete_cache+0xa/0x10
[ 0.372000] ? acpi_ut_delete_caches+0x56/0x7b
[ 0.372000] ? acpi_terminate+0xa/0x14
[ 0.372000] ? acpi_init+0x2af/0x34f
[ 0.372000] ? __class_create+0x4c/0x80
[ 0.372000] ? video_setup+0x7f/0x7f
[ 0.372000] ? acpi_sleep_proc_init+0x27/0x27
[ 0.372000] ? do_one_initcall+0x4e/0x1a0
[ 0.372000] ? kernel_init_freeable+0x189/0x20a
[ 0.372000] ? rest_init+0xc0/0xc0
[ 0.372000] ? kernel_init+0xa/0x100
[ 0.372000] ? ret_from_fork+0x25/0x30
[ 0.388039] kmem_cache_destroy Acpi-parse_ext: Slab cache still has objects
[ 0.389063] CPU: 1 PID: 1 Comm: swapper/0 Tainted: G W
4.12.0-rc4-next-20170608+ #8
[ 0.390557] Hardware name: innotek gmb_h virtual_box/virtual_box, BIOS
virtual_box 12/01/2006
[ 0.392000] Call Trace:
[ 0.392000] ? dump_stack+0x5c/0x81
[ 0.392000] ? kmem_cache_destroy+0x1aa/0x1c0
[ 0.392000] ? acpi_sleep_proc_init+0x27/0x27
[ 0.392000] ? acpi_os_delete_cache+0xa/0x10
[ 0.392000] ? acpi_ut_delete_caches+0x6d/0x7b
[ 0.392000] ? acpi_terminate+0xa/0x14
[ 0.392000] ? acpi_init+0x2af/0x3
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
ata: pata_via: Force PIO for ATAPI devices on VT6415/VT6330
The controller has a hardware bug that can hard hang the system when
doing ATAPI DMAs without any trace of what happened. Depending on the
device attached, it can also prevent the system from booting.
In this case, the system hangs when reading the ATIP from optical media
with cdrecord -vvv -atip on an _NEC DVD_RW ND-4571A 1-01 and an
Optiarc DVD RW AD-7200A 1.06 attached to an ASRock 990FX Extreme 4,
running at UDMA/33.
The issue can be reproduced by running the same command with a cygwin
build of cdrecord on WinXP, although it requires more attempts to cause
it. The hang in that case is also resolved by forcing PIO. It doesn't
appear that VIA has produced any drivers for that OS, thus no known
workaround exists.
HDDs attached to the controller do not suffer from any DMA issues. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: lpfc: Use memcpy() for BIOS version
The strlcat() with FORTIFY support is triggering a panic because it
thinks the target buffer will overflow although the correct target
buffer size is passed in.
Anyway, instead of memset() with 0 followed by a strlcat(), just use
memcpy() and ensure that the resulting buffer is NULL terminated.
BIOSVersion is only used for the lpfc_printf_log() which expects a
properly terminated string. |
| In the Linux kernel, the following vulnerability has been resolved:
jfs: fix array-index-out-of-bounds read in add_missing_indices
stbl is s8 but it must contain offsets into slot which can go from 0 to
127.
Added a bound check for that error and return -EIO if the check fails.
Also make jfs_readdir return with error if add_missing_indices returns
with an error. |
| In the Linux kernel, the following vulnerability has been resolved:
sch_hfsc: make hfsc_qlen_notify() idempotent
hfsc_qlen_notify() is not idempotent either and not friendly
to its callers, like fq_codel_dequeue(). Let's make it idempotent
to ease qdisc_tree_reduce_backlog() callers' life:
1. update_vf() decreases cl->cl_nactive, so we can check whether it is
non-zero before calling it.
2. eltree_remove() always removes RB node cl->el_node, but we can use
RB_EMPTY_NODE() + RB_CLEAR_NODE() to make it safe. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: pcm: Fix race of buffer access at PCM OSS layer
The PCM OSS layer tries to clear the buffer with the silence data at
initialization (or reconfiguration) of a stream with the explicit call
of snd_pcm_format_set_silence() with runtime->dma_area. But this may
lead to a UAF because the accessed runtime->dma_area might be freed
concurrently, as it's performed outside the PCM ops.
For avoiding it, move the code into the PCM core and perform it inside
the buffer access lock, so that it won't be changed during the
operation. |
| In the Linux kernel, the following vulnerability has been resolved:
vhost-scsi: protect vq->log_used with vq->mutex
The vhost-scsi completion path may access vq->log_base when vq->log_used is
already set to false.
vhost-thread QEMU-thread
vhost_scsi_complete_cmd_work()
-> vhost_add_used()
-> vhost_add_used_n()
if (unlikely(vq->log_used))
QEMU disables vq->log_used
via VHOST_SET_VRING_ADDR.
mutex_lock(&vq->mutex);
vq->log_used = false now!
mutex_unlock(&vq->mutex);
QEMU gfree(vq->log_base)
log_used()
-> log_write(vq->log_base)
Assuming the VMM is QEMU. The vq->log_base is from QEMU userpace and can be
reclaimed via gfree(). As a result, this causes invalid memory writes to
QEMU userspace.
The control queue path has the same issue. |
| In the Linux kernel, the following vulnerability has been resolved:
libnvdimm/labels: Fix divide error in nd_label_data_init()
If a faulty CXL memory device returns a broken zero LSA size in its
memory device information (Identify Memory Device (Opcode 4000h), CXL
spec. 3.1, 8.2.9.9.1.1), a divide error occurs in the libnvdimm
driver:
Oops: divide error: 0000 [#1] PREEMPT SMP NOPTI
RIP: 0010:nd_label_data_init+0x10e/0x800 [libnvdimm]
Code and flow:
1) CXL Command 4000h returns LSA size = 0
2) config_size is assigned to zero LSA size (CXL pmem driver):
drivers/cxl/pmem.c: .config_size = mds->lsa_size,
3) max_xfer is set to zero (nvdimm driver):
drivers/nvdimm/label.c: max_xfer = min_t(size_t, ndd->nsarea.max_xfer, config_size);
4) A subsequent DIV_ROUND_UP() causes a division by zero:
drivers/nvdimm/label.c: /* Make our initial read size a multiple of max_xfer size */
drivers/nvdimm/label.c: read_size = min(DIV_ROUND_UP(read_size, max_xfer) * max_xfer,
drivers/nvdimm/label.c- config_size);
Fix this by checking the config size parameter by extending an
existing check. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: lzo - Fix compression buffer overrun
Unlike the decompression code, the compression code in LZO never
checked for output overruns. It instead assumes that the caller
always provides enough buffer space, disregarding the buffer length
provided by the caller.
Add a safe compression interface that checks for the end of buffer
before each write. Use the safe interface in crypto/lzo. |
| In the Linux kernel, the following vulnerability has been resolved:
dm cache: prevent BUG_ON by blocking retries on failed device resumes
A cache device failing to resume due to mapping errors should not be
retried, as the failure leaves a partially initialized policy object.
Repeating the resume operation risks triggering BUG_ON when reloading
cache mappings into the incomplete policy object.
Reproduce steps:
1. create a cache metadata consisting of 512 or more cache blocks,
with some mappings stored in the first array block of the mapping
array. Here we use cache_restore v1.0 to build the metadata.
cat <<EOF >> cmeta.xml
<superblock uuid="" block_size="128" nr_cache_blocks="512" \
policy="smq" hint_width="4">
<mappings>
<mapping cache_block="0" origin_block="0" dirty="false"/>
</mappings>
</superblock>
EOF
dmsetup create cmeta --table "0 8192 linear /dev/sdc 0"
cache_restore -i cmeta.xml -o /dev/mapper/cmeta --metadata-version=2
dmsetup remove cmeta
2. wipe the second array block of the mapping array to simulate
data degradations.
mapping_root=$(dd if=/dev/sdc bs=1c count=8 skip=192 \
2>/dev/null | hexdump -e '1/8 "%u\n"')
ablock=$(dd if=/dev/sdc bs=1c count=8 skip=$((4096*mapping_root+2056)) \
2>/dev/null | hexdump -e '1/8 "%u\n"')
dd if=/dev/zero of=/dev/sdc bs=4k count=1 seek=$ablock
3. try bringing up the cache device. The resume is expected to fail
due to the broken array block.
dmsetup create cmeta --table "0 8192 linear /dev/sdc 0"
dmsetup create cdata --table "0 65536 linear /dev/sdc 8192"
dmsetup create corig --table "0 524288 linear /dev/sdc 262144"
dmsetup create cache --notable
dmsetup load cache --table "0 524288 cache /dev/mapper/cmeta \
/dev/mapper/cdata /dev/mapper/corig 128 2 metadata2 writethrough smq 0"
dmsetup resume cache
4. try resuming the cache again. An unexpected BUG_ON is triggered
while loading cache mappings.
dmsetup resume cache
Kernel logs:
(snip)
------------[ cut here ]------------
kernel BUG at drivers/md/dm-cache-policy-smq.c:752!
Oops: invalid opcode: 0000 [#1] PREEMPT SMP KASAN NOPTI
CPU: 0 UID: 0 PID: 332 Comm: dmsetup Not tainted 6.13.4 #3
RIP: 0010:smq_load_mapping+0x3e5/0x570
Fix by disallowing resume operations for devices that failed the
initial attempt. |
| In the Linux kernel, the following vulnerability has been resolved:
net: pktgen: fix access outside of user given buffer in pktgen_thread_write()
Honour the user given buffer size for the strn_len() calls (otherwise
strn_len() will access memory outside of the user given buffer). |
| In the Linux kernel, the following vulnerability has been resolved:
virtio_ring: Fix data race by tagging event_triggered as racy for KCSAN
syzbot reports a data-race when accessing the event_triggered, here is the
simplified stack when the issue occurred:
==================================================================
BUG: KCSAN: data-race in virtqueue_disable_cb / virtqueue_enable_cb_delayed
write to 0xffff8881025bc452 of 1 bytes by task 3288 on cpu 0:
virtqueue_enable_cb_delayed+0x42/0x3c0 drivers/virtio/virtio_ring.c:2653
start_xmit+0x230/0x1310 drivers/net/virtio_net.c:3264
__netdev_start_xmit include/linux/netdevice.h:5151 [inline]
netdev_start_xmit include/linux/netdevice.h:5160 [inline]
xmit_one net/core/dev.c:3800 [inline]
read to 0xffff8881025bc452 of 1 bytes by interrupt on cpu 1:
virtqueue_disable_cb_split drivers/virtio/virtio_ring.c:880 [inline]
virtqueue_disable_cb+0x92/0x180 drivers/virtio/virtio_ring.c:2566
skb_xmit_done+0x5f/0x140 drivers/net/virtio_net.c:777
vring_interrupt+0x161/0x190 drivers/virtio/virtio_ring.c:2715
__handle_irq_event_percpu+0x95/0x490 kernel/irq/handle.c:158
handle_irq_event_percpu kernel/irq/handle.c:193 [inline]
value changed: 0x01 -> 0x00
==================================================================
When the data race occurs, the function virtqueue_enable_cb_delayed() sets
event_triggered to false, and virtqueue_disable_cb_split/packed() reads it
as false due to the race condition. Since event_triggered is an unreliable
hint used for optimization, this should only cause the driver temporarily
suggest that the device not send an interrupt notification when the event
index is used.
Fix this KCSAN reported data-race issue by explicitly tagging the access as
data_racy. |
| In the Linux kernel, the following vulnerability has been resolved:
media: cx231xx: set device_caps for 417
The video_device for the MPEG encoder did not set device_caps.
Add this, otherwise the video device can't be registered (you get a
WARN_ON instead).
Not seen before since currently 417 support is disabled, but I found
this while experimenting with it. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: mctrl_gpio: split disable_ms into sync and no_sync APIs
The following splat has been observed on a SAMA5D27 platform using
atmel_serial:
BUG: sleeping function called from invalid context at kernel/irq/manage.c:738
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 27, name: kworker/u5:0
preempt_count: 1, expected: 0
INFO: lockdep is turned off.
irq event stamp: 0
hardirqs last enabled at (0): [<00000000>] 0x0
hardirqs last disabled at (0): [<c01588f0>] copy_process+0x1c4c/0x7bec
softirqs last enabled at (0): [<c0158944>] copy_process+0x1ca0/0x7bec
softirqs last disabled at (0): [<00000000>] 0x0
CPU: 0 UID: 0 PID: 27 Comm: kworker/u5:0 Not tainted 6.13.0-rc7+ #74
Hardware name: Atmel SAMA5
Workqueue: hci0 hci_power_on [bluetooth]
Call trace:
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x44/0x70
dump_stack_lvl from __might_resched+0x38c/0x598
__might_resched from disable_irq+0x1c/0x48
disable_irq from mctrl_gpio_disable_ms+0x74/0xc0
mctrl_gpio_disable_ms from atmel_disable_ms.part.0+0x80/0x1f4
atmel_disable_ms.part.0 from atmel_set_termios+0x764/0x11e8
atmel_set_termios from uart_change_line_settings+0x15c/0x994
uart_change_line_settings from uart_set_termios+0x2b0/0x668
uart_set_termios from tty_set_termios+0x600/0x8ec
tty_set_termios from ttyport_set_flow_control+0x188/0x1e0
ttyport_set_flow_control from wilc_setup+0xd0/0x524 [hci_wilc]
wilc_setup [hci_wilc] from hci_dev_open_sync+0x330/0x203c [bluetooth]
hci_dev_open_sync [bluetooth] from hci_dev_do_open+0x40/0xb0 [bluetooth]
hci_dev_do_open [bluetooth] from hci_power_on+0x12c/0x664 [bluetooth]
hci_power_on [bluetooth] from process_one_work+0x998/0x1a38
process_one_work from worker_thread+0x6e0/0xfb4
worker_thread from kthread+0x3d4/0x484
kthread from ret_from_fork+0x14/0x28
This warning is emitted when trying to toggle, at the highest level,
some flow control (with serdev_device_set_flow_control) in a device
driver. At the lowest level, the atmel_serial driver is using
serial_mctrl_gpio lib to enable/disable the corresponding IRQs
accordingly. The warning emitted by CONFIG_DEBUG_ATOMIC_SLEEP is due to
disable_irq (called in mctrl_gpio_disable_ms) being possibly called in
some atomic context (some tty drivers perform modem lines configuration
in regions protected by port lock).
Split mctrl_gpio_disable_ms into two differents APIs, a non-blocking one
and a blocking one. Replace mctrl_gpio_disable_ms calls with the
relevant version depending on whether the call is protected by some port
lock. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: correct the order of prelim_ref arguments in btrfs__prelim_ref
btrfs_prelim_ref() calls the old and new reference variables in the
incorrect order. This causes a NULL pointer dereference because oldref
is passed as NULL to trace_btrfs_prelim_ref_insert().
Note, trace_btrfs_prelim_ref_insert() is being called with newref as
oldref (and oldref as NULL) on purpose in order to print out
the values of newref.
To reproduce:
echo 1 > /sys/kernel/debug/tracing/events/btrfs/btrfs_prelim_ref_insert/enable
Perform some writeback operations.
Backtrace:
BUG: kernel NULL pointer dereference, address: 0000000000000018
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 115949067 P4D 115949067 PUD 11594a067 PMD 0
Oops: Oops: 0000 [#1] SMP NOPTI
CPU: 1 UID: 0 PID: 1188 Comm: fsstress Not tainted 6.15.0-rc2-tester+ #47 PREEMPT(voluntary) 7ca2cef72d5e9c600f0c7718adb6462de8149622
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.3-2-gc13ff2cd-prebuilt.qemu.org 04/01/2014
RIP: 0010:trace_event_raw_event_btrfs__prelim_ref+0x72/0x130
Code: e8 43 81 9f ff 48 85 c0 74 78 4d 85 e4 0f 84 8f 00 00 00 49 8b 94 24 c0 06 00 00 48 8b 0a 48 89 48 08 48 8b 52 08 48 89 50 10 <49> 8b 55 18 48 89 50 18 49 8b 55 20 48 89 50 20 41 0f b6 55 28 88
RSP: 0018:ffffce44820077a0 EFLAGS: 00010286
RAX: ffff8c6b403f9014 RBX: ffff8c6b55825730 RCX: 304994edf9cf506b
RDX: d8b11eb7f0fdb699 RSI: ffff8c6b403f9010 RDI: ffff8c6b403f9010
RBP: 0000000000000001 R08: 0000000000000001 R09: 0000000000000010
R10: 00000000ffffffff R11: 0000000000000000 R12: ffff8c6b4e8fb000
R13: 0000000000000000 R14: ffffce44820077a8 R15: ffff8c6b4abd1540
FS: 00007f4dc6813740(0000) GS:ffff8c6c1d378000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000018 CR3: 000000010eb42000 CR4: 0000000000750ef0
PKRU: 55555554
Call Trace:
<TASK>
prelim_ref_insert+0x1c1/0x270
find_parent_nodes+0x12a6/0x1ee0
? __entry_text_end+0x101f06/0x101f09
? srso_alias_return_thunk+0x5/0xfbef5
? srso_alias_return_thunk+0x5/0xfbef5
? srso_alias_return_thunk+0x5/0xfbef5
? srso_alias_return_thunk+0x5/0xfbef5
btrfs_is_data_extent_shared+0x167/0x640
? fiemap_process_hole+0xd0/0x2c0
extent_fiemap+0xa5c/0xbc0
? __entry_text_end+0x101f05/0x101f09
btrfs_fiemap+0x7e/0xd0
do_vfs_ioctl+0x425/0x9d0
__x64_sys_ioctl+0x75/0xc0 |
