| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| A flaw was found in fig2dev. This vulnerability allows availability via local input manipulation via genge_itp_spline function. |
| A flaw was found in the FreeRDP used by Anaconda's remote install feature, where a crafted RDP packet could trigger a segmentation fault. This issue causes the service to crash and remain defunct, resulting in a denial of service. It occurs pre-boot and is likely due to a NULL pointer dereference. Rebooting is required to recover the system. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7925: prevent NULL vif dereference in mt7925_mac_write_txwi
Check for a NULL `vif` before accessing `ieee80211_vif_is_mld(vif)` to
avoid a potential kernel panic in scenarios where `vif` might not be
initialized. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: sch_dualpi2: drain both C-queue and L-queue in dualpi2_change()
Fix dualpi2_change() to correctly enforce updated limit and memlimit
values after a configuration change of the dualpi2 qdisc.
Before this patch, dualpi2_change() always attempted to dequeue packets
via the root qdisc (C-queue) when reducing backlog or memory usage, and
unconditionally assumed that a valid skb will be returned. When traffic
classification results in packets being queued in the L-queue while the
C-queue is empty, this leads to a NULL skb dereference during limit or
memlimit enforcement.
This is fixed by first dequeuing from the C-queue path if it is
non-empty. Once the C-queue is empty, packets are dequeued directly from
the L-queue. Return values from qdisc_dequeue_internal() are checked for
both queues. When dequeuing from the L-queue, the parent qdisc qlen and
backlog counters are updated explicitly to keep overall qdisc statistics
consistent. |
| In the Linux kernel, the following vulnerability has been resolved:
ice: fix potential NULL pointer deref in error path of ice_set_ringparam()
ice_set_ringparam nullifies tstamp_ring of temporary tx_rings, without
clearing ICE_TX_RING_FLAGS_TXTIME bit.
When ICE_TX_RING_FLAGS_TXTIME is set and the subsequent
ice_setup_tx_ring() call fails, a NULL pointer dereference could happen
in the unwinding sequence:
ice_clean_tx_ring()
-> ice_is_txtime_cfg() == true (ICE_TX_RING_FLAGS_TXTIME is set)
-> ice_free_tx_tstamp_ring()
-> ice_free_tstamp_ring()
-> tstamp_ring->desc (NULL deref)
Clear ICE_TX_RING_FLAGS_TXTIME bit to avoid the potential issue.
Note that this potential issue is found by manual code review.
Compile test only since unfortunately I don't have E830 devices. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: Fix error pointer dereference
The function brcmf_chip_add_core() can return an error pointer and is
not checked. Add checks for error pointer.
Detected by Smatch:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:1010 brcmf_chip_recognition() error:
'core' dereferencing possible ERR_PTR()
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:1013 brcmf_chip_recognition() error:
'core' dereferencing possible ERR_PTR()
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:1016 brcmf_chip_recognition() error:
'core' dereferencing possible ERR_PTR()
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:1019 brcmf_chip_recognition() error:
'core' dereferencing possible ERR_PTR()
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:1022 brcmf_chip_recognition() error:
'core' dereferencing possible ERR_PTR()
[add missing wifi: prefix] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/sun4i: backend: fix error pointer dereference
The function drm_atomic_get_plane_state() can return an error pointer
and is not checked for it. Add error pointer check.
Detected by Smatch:
drivers/gpu/drm/sun4i/sun4i_backend.c:496 sun4i_backend_atomic_check() error:
'plane_state' dereferencing possible ERR_PTR() |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_ldisc: Clear HCI_UART_PROTO_INIT on error
When hci_register_dev() fails in hci_uart_register_dev()
HCI_UART_PROTO_INIT is not cleared before calling hu->proto->close(hu)
and setting hu->hdev to NULL. This means incoming UART data will reach
the protocol-specific recv handler in hci_uart_tty_receive() after
resources are freed.
Clear HCI_UART_PROTO_INIT with a write lock before calling
hu->proto->close() and setting hu->hdev to NULL. The write lock ensures
all active readers have completed and no new reader can enter the
protocol recv path before resources are freed.
This allows the protocol-specific recv functions to remove the
"HCI_UART_REGISTERED" guard without risking a null pointer dereference
if hci_register_dev() fails. |
| In the Linux kernel, the following vulnerability has been resolved:
dm cache: fix null-deref with concurrent writes in passthrough mode
In passthrough mode, when dm-cache starts to invalidate a cache
entry and bio prison cell lock fails due to concurrent write to
the same cached block, mg->cell remains NULL. The error path in
invalidate_complete() attempts to unlock and free the cell
unconditionally, causing a NULL pointer dereference:
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 0 UID: 0 PID: 134 Comm: fio Not tainted 6.19.0-rc7 #3 PREEMPT
RIP: 0010:dm_cell_unlock_v2+0x3f/0x210
<snip>
Call Trace:
invalidate_complete+0xef/0x430
map_bio+0x130f/0x1a10
cache_map+0x320/0x6b0
__map_bio+0x458/0x510
dm_submit_bio+0x40e/0x16d0
__submit_bio+0x419/0x870
<snip>
Reproduce steps:
1. Create a cache device
dmsetup create cmeta --table "0 8192 linear /dev/sdc 0"
dmsetup create cdata --table "0 131072 linear /dev/sdc 8192"
dmsetup create corig --table "0 262144 linear /dev/sdc 262144"
dd if=/dev/zero of=/dev/mapper/cmeta bs=4k count=1 oflag=direct
dmsetup create cache --table "0 262144 cache /dev/mapper/cmeta \
/dev/mapper/cdata /dev/mapper/corig 128 2 metadata2 writethrough smq 0"
2. Promote the first data block into cache
fio --filename=/dev/mapper/cache --name=populate --rw=write --bs=4k \
--direct=1 --size=64k
3. Reload the cache into passthrough mode
dmsetup suspend cache
dmsetup reload cache --table "0 262144 cache /dev/mapper/cmeta \
/dev/mapper/cdata /dev/mapper/corig 128 2 metadata2 passthrough smq 0"
dmsetup resume cache
4. Write to the first cached block concurrently
fio --filename=/dev/mapper/cache --name test --rw=randwrite --bs=4k \
--randrepeat=0 --direct=1 --numjobs=2 --size 64k
Fix by checking if mg->cell is valid before attempting to unlock it. |
| In the Linux kernel, the following vulnerability has been resolved:
nexthop: fix IPv6 route referencing IPv4 nexthop
syzbot reported a panic [1] [2].
When an IPv6 nexthop is replaced with an IPv4 nexthop, the has_v4 flag
of all groups containing this nexthop is not updated. This is because
nh_group_v4_update is only called when replacing AF_INET to AF_INET6,
but the reverse direction (AF_INET6 to AF_INET) is missed.
This allows a stale has_v4=false to bypass fib6_check_nexthop, causing
IPv6 routes to be attached to groups that effectively contain only AF_INET
members. Subsequent route lookups then call nexthop_fib6_nh() which
returns NULL for the AF_INET member, leading to a NULL pointer
dereference.
Fix by calling nh_group_v4_update whenever the family changes, not just
AF_INET to AF_INET6.
Reproducer:
# AF_INET6 blackhole
ip -6 nexthop add id 1 blackhole
# group with has_v4=false
ip nexthop add id 100 group 1
# replace with AF_INET (no -6), has_v4 stays false
ip nexthop replace id 1 blackhole
# pass stale has_v4 check
ip -6 route add 2001:db8::/64 nhid 100
# panic
ping -6 2001:db8::1
[1] https://syzkaller.appspot.com/bug?id=e17283eb2f8dcf3dd9b47fe6f67a95f71faadad0
[2] https://syzkaller.appspot.com/bug?id=8699b6ae54c9f35837d925686208402949e12ef3 |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: Fix error pointer dereference
The variable tps->partner is checked for an error pointer and then if it
is, it sends an error message but does not return and then immediately
dereferenced a few lines below:
tps->partner = typec_register_partner(tps->port, &desc);
if (IS_ERR(tps->partner))
dev_warn(tps->dev, "%s: failed to register partnet\n", __func__);
if (desc.identity) {
typec_partner_set_identity(tps->partner);
cd321x->cur_partner_identity = st.partner_identity;
}
Add early return and fix spelling mistake in error message.
Detected by Smatch:
drivers/usb/typec/tipd/core.c:827 cd321x_update_work() error:
'tps->partner' dereferencing possible ERR_PTR() |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix NULL deref in map_kptr_match_type for scalar regs
Commit ab6c637ad027 ("bpf: Fix a bpf_kptr_xchg() issue with local
kptr") refactored map_kptr_match_type() to branch on btf_is_kernel()
before checking base_type(). A scalar register stored into a kptr
slot has no btf, so the btf_is_kernel(reg->btf) call dereferences
NULL.
Move the base_type() != PTR_TO_BTF_ID guard before any reg->btf
access. |
| IBM WebSphere Application Server and IBM WebSphere Application Server Liberty are vulnerable to denial of service in the WebSphere WebServer Plug-in component when an attacker can pass crafted requests to the web server. |
| In the Linux kernel, the following vulnerability has been resolved:
batman-adv: v: stop OGMv2 on disabled interface
When a batadv_hard_iface is disabled, its mesh_iface pointer is set to
NULL. However, batadv_v_ogm_send_meshif() may still dispatch OGMs via
batadv_v_ogm_queue_on_if() for interfaces that have since lost their
mesh_iface association. This results in a NULL pointer dereference when
batadv_v_ogm_queue_on_if() unconditionally calls netdev_priv() on the
now NULL hard_iface->mesh_iface to retrieve the batadv_priv.
It is necessary to ensure that the batadv_v_ogm_queue_on_if() checks that
it is using the same mesh_iface for which batadv_v_ogm_send_meshif() was
called. |
| In the Linux kernel, the following vulnerability has been resolved:
net/rds: fix NULL deref in rds_ib_send_cqe_handler() on masked atomic completion
rds_ib_xmit_atomic() always programs a masked atomic opcode
(IB_WR_MASKED_ATOMIC_CMP_AND_SWP or IB_WR_MASKED_ATOMIC_FETCH_AND_ADD)
for every RDS atomic cmsg. But the completion-side switch in
rds_ib_send_unmap_op() only handles the non-masked opcodes, so a masked
atomic completion falls through to default and returns rm == NULL while
send->s_op is left set. rds_ib_send_cqe_handler() then dereferences the
NULL rm via rm->m_final_op, oopsing in softirq context. An unprivileged
AF_RDS sendmsg() of an atomic cmsg over an active RDS/IB connection
triggers it; on hardware that natively accepts masked atomics (mlx4,
mlx5) no extra setup is needed.
RDS/IB: rds_ib_send_unmap_op: unexpected opcode 0xd in WR!
Oops: general protection fault [#1] SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000190-0x0000000000000197]
RIP: rds_ib_send_cqe_handler+0x25c/0xb10 (net/rds/ib_send.c:282)
Call Trace:
<IRQ>
rds_ib_send_cqe_handler (net/rds/ib_send.c:282)
poll_scq (net/rds/ib_cm.c:274)
rds_ib_tasklet_fn_send (net/rds/ib_cm.c:294)
tasklet_action_common (kernel/softirq.c:943)
handle_softirqs (kernel/softirq.c:573)
run_ksoftirqd (kernel/softirq.c:479)
</IRQ>
Kernel panic - not syncing: Fatal exception in interrupt
Handle the masked atomic opcodes in the same case as the non-masked
ones: they map to the same struct rds_message.atomic union member, so
the existing container_of()/rds_ib_send_unmap_atomic() body is correct
for them. |
| In the Linux kernel, the following vulnerability has been resolved:
net/smc: avoid NULL deref of conn->lnk in smc_msg_event tracepoint
The smc_msg_event tracepoint class, shared by smc_tx_sendmsg and
smc_rx_recvmsg, unconditionally dereferences smc->conn.lnk:
__string(name, smc->conn.lnk->ibname)
conn->lnk is only set for SMC-R; for SMC-D it is NULL. Other code on
these paths already handles this (e.g. !conn->lnk in
SMC_STAT_RMB_TX_SIZE_SMALL()). With the tracepoint enabled, the first
sendmsg()/recvmsg() on an SMC-D socket crashes:
Oops: general protection fault, probably for non-canonical address
KASAN: null-ptr-deref in range [...]
RIP: 0010:strlen+0x1e/0xa0
Call Trace:
trace_event_raw_event_smc_msg_event (net/smc/smc_tracepoint.h:44)
smc_rx_recvmsg (net/smc/smc_rx.c:515)
smc_recvmsg (net/smc/af_smc.c:2859)
__sys_recvfrom (net/socket.c:2315)
__x64_sys_recvfrom (net/socket.c:2326)
do_syscall_64
The faulting address 0x3e0 is offsetof(struct smc_link, ibname),
confirming the NULL ->lnk deref. Enabling the tracepoint requires
root, but the trigger itself is unprivileged: socket(AF_SMC, ...) has
no capability check, and SMC-D negotiation needs no admin step on
s390 or on x86 with the loopback ISM device loaded.
Log an empty device name for SMC-D instead of dereferencing NULL. |
| GPAC MP4Box v2.4 was discovered to contain a NULL pointer dereference in the gf_isom_add_track_kind() function at isomedia/isom_write.c. This vulnerability allows attackers to cause a Denial of Service (DoS) via a crafted MP4 file. |
| Illustrator versions 29.8.6, 30.3 and earlier are affected by a NULL Pointer Dereference vulnerability that could result in an application denial-of-service. An attacker could exploit this vulnerability to crash the application, leading to a denial-of-service condition. Exploitation of this issue requires user interaction in that a victim must open a malicious file. |
| NULL Pointer Dereference in GitHub repository vim/vim prior to 9.0.1531. |
| A flaw has been found in skvadrik re2c up to 4.4. Impacted is the function check_and_merge_special_rules of the file src/parse/ast.cc. This manipulation causes null pointer dereference. The attack can only be executed locally. The exploit has been published and may be used. Patch name: febeb977936f9519a25d9fbd10ff8256358cdb97. It is suggested to install a patch to address this issue. |
