| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Limit XDomain response copy to actual frame size
tb_xdomain_copy() copies req->response_size bytes from the received
packet buffer regardless of the actual frame size. When a short
response arrives, this reads past the valid frame data in the DMA
pool buffer into stale contents from previous transactions.
Use the minimum of frame size and expected response size for the
copy length. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: RFCOMM: validate skb length in MCC handlers
The RFCOMM MCC handlers cast skb->data to protocol-specific structs
without validating skb->len first. A malicious remote device can send
truncated MCC frames and trigger out-of-bounds reads in these handlers.
Fix this by using skb_pull_data() to validate and access the required
data before dereferencing it.
rfcomm_recv_rpn() requires special handling since ETSI TS 07.10 allows
1-byte RPN requests. Handle this by validating only the DLCI byte first,
and validating the full struct only when len > 1. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: conntrack_irc: fix possible out-of-bounds read
When parsing fails after we've matched the command string we
should bail out instead of trying to match a different command.
This helper should be deprecated, given prevalence of TLS I doubt it has
any relevance in 2026. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: validate cached peer INIT chunk length in COOKIE_ECHO processing
When a listening SCTP server processes a COOKIE_ECHO chunk, the cached
peer INIT chunk embedded after the cookie is parsed and its parameters
are later walked by sctp_process_init() using sctp_walk_params().
However, the chunk header length of this cached INIT chunk was not
validated against the remaining buffer in the COOKIE_ECHO payload. If
the length field is inflated, the parameter walk can run beyond the
actual received data, leading to out-of-bounds reads and potential
memory corruption during later parameter handling (e.g. STATE_COOKIE
processing and kmemdup() copies).
Add a bounds check in sctp_unpack_cookie() to ensure the cached INIT
chunk length does not exceed the available data in the COOKIE_ECHO
buffer before it is used. |
| In the Linux kernel, the following vulnerability has been resolved:
net: guard timestamp cmsgs to real error queue skbs
skb_is_err_queue() treats PACKET_OUTGOING as the sole marker for an skb
from sk_error_queue. That assumption is not true for AF_PACKET sockets:
outgoing packet taps are also delivered to packet sockets with
skb->pkt_type == PACKET_OUTGOING, but their skb->cb is owned by AF_PACKET
instead of struct sock_exterr_skb.
If such an skb is received with timestamping enabled, the generic
timestamp cmsg path can read AF_PACKET control-buffer state as
sock_exterr_skb::opt_stats. With SO_RXQ_OVFL enabled, the packet drop
counter overlaps opt_stats. An odd drop count makes the path emit
SCM_TIMESTAMPING_OPT_STATS with skb->len and skb->data. For non-linear
skbs this copies past the linear head and can trigger hardened usercopy or
disclose adjacent heap contents.
Keep skb_is_err_queue() local to net/socket.c, but make it verify that
the PACKET_OUTGOING marker is paired with the sock_rmem_free destructor
installed by sock_queue_err_skb(). AF_PACKET receive skbs use normal
receive ownership and no longer pass as error-queue skbs, while legitimate
sk_error_queue entries keep the PACKET_OUTGOING marker and sock_rmem_free
ownership. |
| In the Linux kernel, the following vulnerability has been resolved:
ip6_vti: fix incorrect tunnel matching in vti6_tnl_lookup()
In vti6_tnl_lookup(), when an exact match for a tunnel fails,
the code falls back to searching for wildcard tunnels:
- Tunnels matching the packet's local address, with any remote address
wildcard remote).
- Tunnels matching the packet's remote address, with any local address
(wildcard local).
However, vti6 stores all these different types of tunnels in the same
hash table (ip6n->tnls_r_l) prone to hash collisions.
The bug is that the fallback search loops in vti6_tnl_lookup() were
missing checks to ensure that the candidate tunnel actually has
a wildcard address. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: reject oversized Broadcast Announcement prepend
Existing advertising instances can already hold the maximum extended
advertising payload. When hci_adv_bcast_annoucement() prepends the
Broadcast Announcement service data to that payload, the combined data
may no longer fit in the temporary buffer used to rebuild the
advertising data.
Reject that case before copying the existing payload and report the
failure through the device log. This keeps the existing advertising
data intact and avoids overrunning the temporary buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/ivpu: Add buffer overflow check in MS get_info_ioctl
Add validation that the info size returned from the metric stream info
query is not exceeded when checked against the allocated buffer size.
If the firmware returns a size larger than the buffer, reject the
operation with -EOVERFLOW instead of proceeding with an incorrect
buffer copy. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring/net: inherit IORING_CQE_F_BUF_MORE across bundle recv retries
When a bundle recv retries inside io_recv_finish(), the merge logic OR
the saved cflags from the previous iteration with the cflags returned by
the new iteration:
cflags = req->cqe.flags | (cflags & CQE_F_MASK);
Bits listed in CQE_F_MASK are inherited from the new iteration, and all
other bits (notably IORING_CQE_F_BUFFER and the buffer ID) come from the
saved cflags. Before this change CQE_F_MASK covered only
IORING_CQE_F_SOCK_NONEMPTY and IORING_CQE_F_MORE.
When using provided buffer rings (IOU_PBUF_RING_INC) with incremental
mode, and bundle recv, io_kbuf_inc_commit() can leave the head ring
entry partially consumed, __io_put_kbufs() then sets
IORING_CQE_F_BUF_MORE on the returned cflags so userspace knows the
buffer ID will be reused for subsequent completions.
Because IORING_CQE_F_BUF_MORE was not in CQE_F_MASK, the merge above
silently dropped it whenever the final retry iteration partially
consumed the buffer, and the subsequent req->cqe.flags = cflags &
~CQE_F_MASK save would have left a stale IORING_CQE_F_BUF_MORE in the
carried-over cflags had one been present. Userspace would then
wrongfully advance it ring head past an entry the kernel still uses.
Add IORING_CQE_F_BUF_MORE to CQE_F_MASK so it is both inherited from the
new iteration into the user-visible CQE and stripped from the saved
cflags between iterations. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/core: Validate cpu_id against nr_cpu_ids in DMAH alloc
The cpu_id attribute supplied by user space through
UVERBS_ATTR_ALLOC_DMAH_CPU_ID is passed directly to cpumask_test_cpu()
without first verifying that the value is within the valid CPU range.
Passing such untrusted data to cpumask_test_cpu() may lead to an
out-of-bounds read of the underlying cpumask bitmap: the helper expands
to a test_bit() that indexes the bitmap by cpu_id / BITS_PER_LONG with
no bound check.
In addition, on kernels built with CONFIG_DEBUG_PER_CPU_MAPS it trips
the WARN_ON_ONCE() in cpumask_check(); combined with panic_on_warn this
turns a bad user input into a machine reboot.
Reject any cpu_id that is not smaller than nr_cpu_ids with -EINVAL
before it is used.
Reported by Smatch. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/ethosu: fix IFM region index out-of-bounds in command stream parser
NPU_SET_IFM_REGION extracts the region index with param & 0x7f, giving
a maximum value of 127. However region_size[] and output_region[] in
struct ethosu_validated_cmdstream_info are both sized to
NPU_BASEP_REGION_MAX (8), giving valid indices [0..7].
Every other region assignment in the same switch uses param & 0x7:
NPU_SET_OFM_REGION: st.ofm.region = param & 0x7;
NPU_SET_IFM2_REGION: st.ifm2.region = param & 0x7;
NPU_SET_WEIGHT_REGION: st.weight[0].region = param & 0x7;
NPU_SET_SCALE_REGION: st.scale[0].region = param & 0x7;
The 0x7f mask on IFM is inconsistent and appears to be a typo.
feat_matrix_length() and calc_sizes() use the region index directly
as an array subscript into the kzalloc'd info struct:
info->region_size[fm->region] = max(...);
A userspace caller supplying NPU_SET_IFM_REGION with param > 7 causes
a write up to 127*8 = 1016 bytes past the start of region_size[],
corrupting adjacent kernel heap data.
Fix by applying the same & 0x7 mask used by all other region
assignments. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix the ACK parser to extract the SACK table for parsing
Fix modification of the received skbuff in rxrpc_input_soft_acks() and a
potential incorrect access of the buffer in a fragmented UDP packet (the
packet would probably have to be deliberately pre-generated as fragmented)
when AF_RXRPC tries to extract the contents of the SACK table by copying
out the contents of the SACK table into a buffer before attempting to parse
AF_RXRPC assumes that it can just call skb_condense() and then validly
access the SACK table from skb->data and that it will be a flat buffer -
but skb_condense() can silently fail to do anything under some
circumstances.
Note that whilst rxrpc_input_soft_acks() should be able to parse extended
ACKs, the rest of AF_RXRPC doesn't currently support that.
Further, there's then no need to call skb_condense() in rxrpc_input_ack(),
so don't. |
| In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Validate XDomain request packet size before type cast
tb_xdp_handle_request() casts the received packet buffer to
protocol-specific structs without verifying that the allocation
is large enough for the target type. A peer can send a minimal
XDomain packet that passes the generic header length check but is
shorter than the struct accessed after the cast, causing out-of-
bounds reads from the kmemdup allocation.
Plumb the packet length through xdomain_request_work and validate
it against the expected struct size before each cast. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: require Ethernet MAC header before using eth_hdr()
`ip6t_eui64`, `xt_mac`, the `bitmap:ip,mac`, `hash:ip,mac`, and
`hash:mac` ipset types, and `nf_log_syslog` access `eth_hdr(skb)`
after either assuming that the skb is associated with an Ethernet
device or checking only that the `ETH_HLEN` bytes at
`skb_mac_header(skb)` lie between `skb->head` and `skb->data`.
Make these paths first verify that the skb is associated with an
Ethernet device, that the MAC header was set, and that it spans at
least a full Ethernet header before accessing `eth_hdr(skb)`. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix same-register dst/src OOB read and pointer leak in sock_ops
When a BPF sock_ops program accesses ctx fields with dst_reg == src_reg,
the SOCK_OPS_GET_SK() and SOCK_OPS_GET_FIELD() macros fail to zero the
destination register in the !fullsock / !locked_tcp_sock path.
Both macros borrow a temporary register to check is_fullsock /
is_locked_tcp_sock when dst_reg == src_reg, because dst_reg holds the
ctx pointer. When the check is false (e.g., TCP_NEW_SYN_RECV state with
a request_sock), dst_reg should be zeroed but is not, leaving the stale
ctx pointer:
- SOCK_OPS_GET_SK: dst_reg retains the ctx pointer, passes NULL checks
as PTR_TO_SOCKET_OR_NULL, and can be used as a bogus socket pointer,
leading to stack-out-of-bounds access in helpers like
bpf_skc_to_tcp6_sock().
- SOCK_OPS_GET_FIELD: dst_reg retains the ctx pointer which the
verifier believes is a SCALAR_VALUE, leaking a kernel pointer.
Fix both macros by:
- Changing JMP_A(1) to JMP_A(2) in the fullsock path to skip the
added instruction.
- Adding BPF_MOV64_IMM(si->dst_reg, 0) after the temp register
restore in the !fullsock path, placed after the restore because
dst_reg == src_reg means we need src_reg intact to read ctx->temp. |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2/dlm: validate qr_numregions in dlm_match_regions()
Patch series "ocfs2/dlm: fix two bugs in dlm_match_regions()".
In dlm_match_regions(), the qr_numregions field from a DLM_QUERY_REGION
network message is used to drive loops over the qr_regions buffer without
sufficient validation. This series fixes two issues:
- Patch 1 adds a bounds check to reject messages where qr_numregions
exceeds O2NM_MAX_REGIONS. The o2net layer only validates message
byte length; it does not constrain field values, so a crafted message
can set qr_numregions up to 255 and trigger out-of-bounds reads past
the 1024-byte qr_regions buffer.
- Patch 2 fixes an off-by-one in the local-vs-remote comparison loop,
which uses '<=' instead of '<', reading one entry past the valid range
even when qr_numregions is within bounds.
This patch (of 2):
The qr_numregions field from a DLM_QUERY_REGION network message is used
directly as loop bounds in dlm_match_regions() without checking against
O2NM_MAX_REGIONS. Since qr_regions is sized for at most O2NM_MAX_REGIONS
(32) entries, a crafted message with qr_numregions > 32 causes
out-of-bounds reads past the qr_regions buffer.
Add a bounds check for qr_numregions before entering the loops. |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2: validate bg_bits during freefrag scan
[BUG]
A crafted filesystem can trigger an out-of-bounds bitmap walk when
OCFS2_IOC_INFO is issued with OCFS2_INFO_FL_NON_COHERENT.
BUG: KASAN: use-after-free in instrument_atomic_read include/linux/instrumented.h:68 [inline]
BUG: KASAN: use-after-free in _test_bit include/asm-generic/bitops/instrumented-non-atomic.h:141 [inline]
BUG: KASAN: use-after-free in test_bit_le include/asm-generic/bitops/le.h:21 [inline]
BUG: KASAN: use-after-free in ocfs2_info_freefrag_scan_chain fs/ocfs2/ioctl.c:495 [inline]
BUG: KASAN: use-after-free in ocfs2_info_freefrag_scan_bitmap fs/ocfs2/ioctl.c:588 [inline]
BUG: KASAN: use-after-free in ocfs2_info_handle_freefrag fs/ocfs2/ioctl.c:662 [inline]
BUG: KASAN: use-after-free in ocfs2_info_handle_request+0x1c66/0x3370 fs/ocfs2/ioctl.c:754
Read of size 8 at addr ffff888031bce000 by task syz.0.636/1435
Call Trace:
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0xbe/0x130 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0xd1/0x650 mm/kasan/report.c:482
kasan_report+0xfb/0x140 mm/kasan/report.c:595
check_region_inline mm/kasan/generic.c:186 [inline]
kasan_check_range+0x11c/0x200 mm/kasan/generic.c:200
__kasan_check_read+0x11/0x20 mm/kasan/shadow.c:31
instrument_atomic_read include/linux/instrumented.h:68 [inline]
_test_bit include/asm-generic/bitops/instrumented-non-atomic.h:141 [inline]
test_bit_le include/asm-generic/bitops/le.h:21 [inline]
ocfs2_info_freefrag_scan_chain fs/ocfs2/ioctl.c:495 [inline]
ocfs2_info_freefrag_scan_bitmap fs/ocfs2/ioctl.c:588 [inline]
ocfs2_info_handle_freefrag fs/ocfs2/ioctl.c:662 [inline]
ocfs2_info_handle_request+0x1c66/0x3370 fs/ocfs2/ioctl.c:754
ocfs2_info_handle+0x18d/0x2a0 fs/ocfs2/ioctl.c:828
ocfs2_ioctl+0x632/0x6e0 fs/ocfs2/ioctl.c:913
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:597 [inline]
__se_sys_ioctl fs/ioctl.c:583 [inline]
__x64_sys_ioctl+0x197/0x1e0 fs/ioctl.c:583
...
[CAUSE]
ocfs2_info_freefrag_scan_chain() uses on-disk bg_bits directly as the
bitmap scan limit. The coherent path reads group descriptors through
ocfs2_read_group_descriptor(), which validates the descriptor before
use. The non-coherent path uses ocfs2_read_blocks_sync() instead and
skips that validation, so an impossible bg_bits value can drive the
bitmap walk past the end of the block.
[FIX]
Compute the bitmap capacity from the filesystem format with
ocfs2_group_bitmap_size(), report descriptors whose bg_bits exceeds
that limit, and clamp the scan to the computed capacity. This keeps the
freefrag report going while avoiding reads beyond the buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nfnetlink_osf: fix out-of-bounds read on option matching
In nf_osf_match(), the nf_osf_hdr_ctx structure is initialized once
and passed by reference to nf_osf_match_one() for each fingerprint
checked. During TCP option parsing, nf_osf_match_one() advances the
shared ctx->optp pointer.
If a fingerprint perfectly matches, the function returns early without
restoring ctx->optp to its initial state. If the user has configured
NF_OSF_LOGLEVEL_ALL, the loop continues to the next fingerprint.
However, because ctx->optp was not restored, the next call to
nf_osf_match_one() starts parsing from the end of the options buffer.
This causes subsequent matches to read garbage data and fail
immediately, making it impossible to log more than one match or logging
incorrect matches.
Instead of using a shared ctx->optp pointer, pass the context as a
constant pointer and use a local pointer (optp) for TCP option
traversal. This makes nf_osf_match_one() strictly stateless from the
caller's perspective, ensuring every fingerprint check starts at the
correct option offset. |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: Fix potential out-of-bounds access in osdmap_decode()
When decoding osd_state and osd_weight from an incoming osdmap in
osdmap_decode(), both are decoded for each osd, i.e., map->max_osd
times. The ceph_decode_need() check only accounts for
sizeof(*map->osd_weight) once. This can potentially result in an
out-of-bounds memory access if the incoming message is corrupted such
that the max_osd value exceeds the actual content of the osdmap message.
This patch fixes the issue by changing the corresponding part in the
ceph_decode_need() check to account for
map->max_osd*sizeof(*map->osd_weight). |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: Fix potential null-ptr-deref in decode_choose_args()
A message of type CEPH_MSG_OSD_MAP contains an OSD map that itself
contains a CRUSH map. When decoding this CRUSH map in crush_decode(), an
array of max_buckets CRUSH buckets is decoded, where some indices may
not refer to actual buckets and are therefore set to NULL. The received
CRUSH map may optionally contain choose_args that get decoded in
decode_choose_args(). When decoding a crush_choose_arg_map, a series of
choose_args for different buckets is decoded, with the bucket_index
being read from the incoming message. It is only checked that the bucket
index does not exceed max_buckets, but not that it doesn't point to an
index with a NULL bucket. If a (potentially corrupted) message contains
a crush_choose_arg_map including such a bucket_index, a null pointer
dereference may occur in the subsequent processing when attempting to
access the bucket with the given index.
This patch fixes the issue by extending the affected check. Now, it is
only attempted to access the bucket if it is not NULL. |
