In the Linux kernel, the following vulnerability has been resolved:
arm64: contpte: fix set_access_flags() no-op check for SMMU/ATS faults
contpte_ptep_set_access_flags() compared the gathered ptep_get() value
against the requested entry to detect no-ops. ptep_get() ORs AF/dirty
from all sub-PTEs in the CONT block, so a dirty sibling can make the
target appear already-dirty. When the gathered value matches entry, the
function returns 0 even though the target sub-PTE still has PTE_RDONLY
set in hardware.
For a CPU with FEAT_HAFDBS this gathered view is fine, since hardware may
set AF/dirty on any sub-PTE and CPU TLB behavior is effectively gathered
across the CONT range. But page-table walkers that evaluate each
descriptor individually (e.g. a CPU without DBM support, or an SMMU
without HTTU, or with HA/HD disabled in CD.TCR) can keep faulting on the
unchanged target sub-PTE, causing an infinite fault loop.
Gathering can therefore cause false no-ops when only a sibling has been
updated:
- write faults: target still has PTE_RDONLY (needs PTE_RDONLY cleared)
- read faults: target still lacks PTE_AF
Fix by checking each sub-PTE against the requested AF/dirty/write state
(the same bits consumed by __ptep_set_access_flags()), using raw
per-PTE values rather than the gathered ptep_get() view, before
returning no-op. Keep using the raw target PTE for the write-bit unfold
decision.
Per Arm ARM (DDI 0487) D8.7.1 ("The Contiguous bit"), any sub-PTE in a CONT
range may become the effective cached translation and software must
maintain consistent attributes across the range.
arm64: contpte: fix set_access_flags() no-op check for SMMU/ATS faults
contpte_ptep_set_access_flags() compared the gathered ptep_get() value
against the requested entry to detect no-ops. ptep_get() ORs AF/dirty
from all sub-PTEs in the CONT block, so a dirty sibling can make the
target appear already-dirty. When the gathered value matches entry, the
function returns 0 even though the target sub-PTE still has PTE_RDONLY
set in hardware.
For a CPU with FEAT_HAFDBS this gathered view is fine, since hardware may
set AF/dirty on any sub-PTE and CPU TLB behavior is effectively gathered
across the CONT range. But page-table walkers that evaluate each
descriptor individually (e.g. a CPU without DBM support, or an SMMU
without HTTU, or with HA/HD disabled in CD.TCR) can keep faulting on the
unchanged target sub-PTE, causing an infinite fault loop.
Gathering can therefore cause false no-ops when only a sibling has been
updated:
- write faults: target still has PTE_RDONLY (needs PTE_RDONLY cleared)
- read faults: target still lacks PTE_AF
Fix by checking each sub-PTE against the requested AF/dirty/write state
(the same bits consumed by __ptep_set_access_flags()), using raw
per-PTE values rather than the gathered ptep_get() view, before
returning no-op. Keep using the raw target PTE for the write-bit unfold
decision.
Per Arm ARM (DDI 0487) D8.7.1 ("The Contiguous bit"), any sub-PTE in a CONT
range may become the effective cached translation and software must
maintain consistent attributes across the range.
Advisories
No advisories yet.
Fixes
Solution
No solution given by the vendor.
Workaround
No workaround given by the vendor.
References
History
Wed, 13 May 2026 18:45:00 +0000
| Type | Values Removed | Values Added |
|---|---|---|
| Weaknesses | CWE-715 CWE-730 |
Wed, 13 May 2026 15:15:00 +0000
| Type | Values Removed | Values Added |
|---|---|---|
| Description | In the Linux kernel, the following vulnerability has been resolved: arm64: contpte: fix set_access_flags() no-op check for SMMU/ATS faults contpte_ptep_set_access_flags() compared the gathered ptep_get() value against the requested entry to detect no-ops. ptep_get() ORs AF/dirty from all sub-PTEs in the CONT block, so a dirty sibling can make the target appear already-dirty. When the gathered value matches entry, the function returns 0 even though the target sub-PTE still has PTE_RDONLY set in hardware. For a CPU with FEAT_HAFDBS this gathered view is fine, since hardware may set AF/dirty on any sub-PTE and CPU TLB behavior is effectively gathered across the CONT range. But page-table walkers that evaluate each descriptor individually (e.g. a CPU without DBM support, or an SMMU without HTTU, or with HA/HD disabled in CD.TCR) can keep faulting on the unchanged target sub-PTE, causing an infinite fault loop. Gathering can therefore cause false no-ops when only a sibling has been updated: - write faults: target still has PTE_RDONLY (needs PTE_RDONLY cleared) - read faults: target still lacks PTE_AF Fix by checking each sub-PTE against the requested AF/dirty/write state (the same bits consumed by __ptep_set_access_flags()), using raw per-PTE values rather than the gathered ptep_get() view, before returning no-op. Keep using the raw target PTE for the write-bit unfold decision. Per Arm ARM (DDI 0487) D8.7.1 ("The Contiguous bit"), any sub-PTE in a CONT range may become the effective cached translation and software must maintain consistent attributes across the range. | |
| Title | arm64: contpte: fix set_access_flags() no-op check for SMMU/ATS faults | |
| First Time appeared |
Linux
Linux linux Kernel |
|
| CPEs | cpe:2.3:o:linux:linux_kernel:*:*:*:*:*:*:*:* | |
| Vendors & Products |
Linux
Linux linux Kernel |
|
| References |
|
Projects
Sign in to view the affected projects.
Status: PUBLISHED
Assigner: Linux
Published:
Updated: 2026-05-13T15:08:32.085Z
Reserved: 2026-05-01T14:12:56.012Z
Link: CVE-2026-43486
No data.
Status : Received
Published: 2026-05-13T16:16:51.880
Modified: 2026-05-13T16:16:51.880
Link: CVE-2026-43486
No data.
OpenCVE Enrichment
Updated: 2026-05-13T18:30:46Z